Modification of asphalt binders has been one of the common techniques to overcome the climatic and traffic-related distresses that develop in bituminous materials. Over the past decade, many new methods of incorporating recycled tire rubber as a modifier have been developed and evaluated by states and county road departments. This study focuses on the use of the so-called devulcanized recycled tire rubber modifier and its effects on the performance grade, fatigue cracking resistance, and rutting resistance of asphalt binder. Devulcanized rubber was incorporated into hot liquid asphalt at various percentages using high and low shear blending, consecutively. First, the effect of modifications on continuous performance grades (PG) at low, intermediate, and high temperatures was investigated. Second, equistiffness temperatures of the binder-rubber mixes were established, and the fatigue cracking resistances of the rubber-binder blends were measured by using the linear amplitude sweep (LAS) test at different strain levels. Last, the multiple stress creep and recovery test (MSCR) was conducted on the modified asphalt samples to characterize the high-temperature performance. Although there was a significant improvement on high PG as the modifier amount increased, the improvement for intermediate and low PGs was minimal. The same trend observed for high PG of the modified asphalt binders was also obtained for fatigue cracking resistance and rutting resistance. The results showed that the use of devulcanized rubber modification could successfully extend the life of bituminous materials.
7 June 2023 in Construction and Building Materials
Use of recycled/reclaimed asphalt pavement (RAP) leads to economic as well as environmental benefits. However, increasing the percentage of RAP in a new asphalt pavement may hinder the economic benefits due to the necessity of expensive softer binders used to compensate for RAP stiffening effect. Alternatively, this problem may potentially be overcome by use of another recycled material: crumb rubber (CR). In this study, linear viscoelastic, thermal and fatigue cracking properties of mixtures prepared with different rubberised asphalt binders were compared with the soft binders. The scope of the testing included asphalt mixtures produced from the following binders; (i) devulcanised rubber, (ii) CR terminally blend, (iii) CR wet process, (iv) soft binder (PG 58-34) and (v) base (control) binder (PG 58-28). The results of the fatigue tests indicated that CR-modified asphalt mixtures made with the base binder (PG58-28) outperformed the mixture made with grade bumped (PG58-34) binder. Similar results were observed in low-temperature cracking tests. The results indicated that the CR-modified binders can be used in lieu of grade bumping of binders in high RAP mixtures. In fatigue cracking tests, among the three CR technologies, wet process outperformed terminally blend and devulcanised rubber at high temperatures and high strain levels at low temperatures. At relatively low strain levels, terminally blend was the best performer in low temperature. In low-temperature cracking tests, devulcanised rubber exhibited highest tensile strength, but lowest fracture energy. Wet process exhibited highest fracture energy and lowest strength.
1 January 2017 in Transportation Research Record: Journal of the Transportation Research Board
Three major methods are used to produce crumb rubber modified asphalt pavement: the dry process (CRDry), the terminal blend process (CRTB), and the wet process (CRWet). Although the CRDry process replaces the portion of fine aggregate in the asphalt mixture with crumb rubber (CR) particles, the CRWet process incorporates CR particles into hot liquid asphalt before it is mixed with aggregates. CRTB is known as a special type of CRWet process in which the CR is blended with asphalt binder at the asphalt terminal. In general, the CRWet process can integrate 15% to 22% CR by weight of the binder. This amount ranges from 10% to 12% in the CRTB process as a result of the limitations associated with transportation and pumping. This study investigated the feasibility of increasing the CR content of CRTB modified asphalt mixtures. The addition to the mixture of about 0.5% CR (by weight of the mix) through the CRDry process doubled the amount of rubber to be found in a conventional CRTB mix. The relative performances of the CRTB and the CRTB+CRDry processes [i.e., crumb rubber hybrid (CRHY)] were investigated with respect to their linear viscoelastic properties, rutting susceptibility, moisture damage, resistance to fatigue, and low temperature cracking. It was shown that it was possible to increase the amount of CR in the mixture through the use of the CRHY method proposed here, without adverse effect on the performance of the mixture.