Syed Haider

Dr. Syed Haider

orcid

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 December 2007 in Journal of Transportation Engineering
Verified
Journal Article
Closed access
Syed HaiderSyed Haider
Syed Haider
RHRonald S. Harichandran
Ronald S. Harichandran
Axle load spectra have been used to develop the mechanistic-empirical pavement design guide (M-E PDG). Use of these load spectra provides a more direct and rational approach for the analysis and design of pavement structures to estimate the effects of actual traffic on pavement response and distress. However, the demand for specific truck- and axle load-related data makes the collection of axle load spectra a very complicated, costly, and labor-intensive operation. Due to limited resources available in state and local highway agencies for traffic data collection, the M-E PDG allows for various levels of traffic data collection and analysis. These levels vary from site-specific (Level 1) to regional average (Level 3) traffic load and volume data. This paper explores the possibility of extracting axle loads from truck weight and volume data and presents a practical method of modeling axle load spectra. Axle load-related data used in the analyses cover diversified geographical locations in the United States....

5 August 2020 in Transportation Research Record: Journal of the Transportation Research Board
Verified
Journal Article
Closed access
PDF file
Syed HaiderSyed Haider
Syed Haider
MMMuhamad Munum Masud
Muhamad Munum Masud
OSOlga Selezneva
Olga Selezneva
DWDean J. Wolf
Dean J. Wolf
Weigh-in-motion (WIM) is a primary technology used for monitoring and collecting vehicle weights and axle loads on roadways. Highway agencies collect WIM data for many reasons, including highway planning, pavement and bridge design, freight movement studies, motor vehicle enforcement, and regulatory studies. Therefore, the data collected at WIM systems must be accurate and represent actual field loadings. Several factors or field conditions can affect the WIM system accuracy (i.e., measurement error). The potential site-related factors include road geometry, pavement stiffness, pavement surface distresses, road roughness, and climate. The WIM calibration and equipment-related factors may include sensor type and array, calibration speed and speed points, and sensors’ age. The WIM data for Long-Term Pavement Performance (LTPP) research-quality sites were considered to estimate benchmark accuracies for different sensors and evaluate the effects of different factors on WIM measurement errors. These are the 35 sites with WIM calibration data that meet the ASTM E1318-09 error tolerances for Type I WIM systems and are consistently calibrated using the LTPP protocol with a complete set of supporting data about WIM site performance and WIM site conditions. The data for the LTPP research-quality sites showed that for the sensor arrays utilized, the best achievable total errors based on GVW are ±5% for load cell (LC), ±9% for bending plate (BP), and ±9.8% for the quartz piezo (QP) sensors. These accuracy levels for different sensor types provide highway agencies with the benchmark values demonstrating the practically achievable accuracy of WIM measurements after calibration for different WIM sensor types. Based on available data, WIM sensor accuracy can be significantly affected by climate, especially for QP and polymer piezo sensors. Also, the longitudinal roadway slope at a WIM site, sensor array, and speed points may significantly affect the WIM system accuracy.


1 December 2009 in Journal of Transportation Engineering
Verified
Journal Article
Closed access
Syed HaiderSyed Haider
Syed Haider
RHRonald S. Harichandran
Ronald S. Harichandran
MDMonther B. Dwaikat
Monther B. Dwaikat
The mechanistic-empirical (ME) design procedures utilize axle load spectra to characterize the individual traffic loadings for a site. These loading characteristics are employed to calculate pavement response and for subsequent damage computations. Generally, these axle load distributions exhibit a bimodal shape and a combination of two continuous statistical distributions can be used to model them. In this paper, closed-form solutions are developed to estimate the parameters of the bimodal distribution from data. A combination of two normal distributions is shown to reasonably fit observed axle spectra. Since it is anticipated that the AASHTO equivalent single-axle load (ESAL) concept will continue to be used by pavement engineers even after the full adoption of ME design methods, a closed-form statistical relationship between ESALs and axle load spectra is proposed. Such a relationship will be useful in estimating a traffic level index from an axle distribution. In addition, the relationship can provide...

26 February 2009 in International Journal of Pavement Engineering
Verified
Journal Article
Closed access
Syed HaiderSyed Haider
Syed Haider
KCKarim Chatti
Karim Chatti
This paper presents the results of a study on the relative influence of design features and site factors on the fatigue performance of in-service flexible pavements. The data used in this study were from the SPS-1 experiment of the long-term performance pavement (LTPP) programme. This experiment was designed to investigate the effects of hot mix asphalt (HMA) surface layer thickness, base type, base thickness and drainage on the performance of new flexible pavements constructed in different site conditions (subgrade type and climate). Various statistical analyses (ANOVA, logistic regression, discriminant analysis) were adopted for data analyses. Among the design factors, base type was found to be the most critical factor affecting fatigue cracking. The best performance was shown by pavement sections with asphalt treated base (ATB). This effect should be interpreted in light of the fact that an ATB effectively means a thicker HMA layer. The combination of drainage and base type also played an important role in improving fatigue performance. Base thickness had a negligible effect while climatic conditions were found to have a significant effect with more fatigue-cracking occurrence in wet-freeze environment. Also, in general, pavements built on fine-grained soils showed the worst performance. Most of the findings from this study support the existing understanding of pavement fatigue performance. Yet, the analyses of data from in-service pavements in this study provide an overview of the interactions between design and site factors and provide new insights on various design options to achieve better long-term pavement performance.

11 March 2011
Verified
Conference Paper
Closed access
Syed HaiderSyed Haider
Syed Haider
MMM. Waseem Mirza
M. Waseem Mirza
ATAshvini K. Thottempudi
Ashvini K. Thottempudi
JBJaved Bari
Javed Bari
GBGilbert Y. Baladi
Gilbert Y. Baladi
The temperature-viscosity relationships for twenty two neat and modified asphalt binders were evaluated using conventional tests (CT) such as penetration, kinematic and absolute viscosities, and ring and ball softening point; rotational viscometer (RV); and dynamic shear rheometer (DSR). The temperature ranged from 25 to 135 °C, 100 to 185 °C, and 7 to 82 °C for conventional, RV, and DSR tests, respectively. Results from several binders studies have revealed that binders having similar penetration, viscosity and performance grade (PG) could show dissimilar rheological behaviors. Hence, there is a need to fully characterize asphalt binders to capture their rheology over a wide range of temperatures and loading frequencies. The activation energy (AE) concept was utilized in this study to characterize the temperature susceptibility of the asphalt binders. Correlations between AE and binder rheological properties (e.g., G*/sinδ and G* sinδ) were evaluated. In addition, a relationship between AE and useful temperature range (UTR) determined from the performance grades (PG) was developed. The advantages of characterizing the relative temperature susceptibility of the binders using AE are discussed. Finally, discussion on mixing and compaction temperatures, especially for polymer modified binders, by using AE is also included in this paper.