Antimicrobial resistance (AMR) is a neglected issue that poses a serious global threat to public health, causing long-term negative consequences at both humanitarian and economic levels. Herein, we report an unprecedented economic fabrication method of seven potentiometric screen-printed sensors for the ultra-trace determination of gemifloxacin (GEMI) as a model of the fluoroquinolones antibiotics deeply involved in the growing AMR problem. Sensors were constructed by depositing homemade carbon ink on a recycled X-ray sheet, patterned using stencils printed with an office printer in simple, cost-effective steps requiring no sophisticated equipment. Four sensors were modified using carbon quantum dots (CQDs) synthesized from dextrose through a single-step method. Sensors exhibited a linear response in the concentration ranges 10−5–10−2 M (sensors 1, 3 and 4), 10−6–10−3 M (sensor 2) and 10−6–10−2 M (sensors 5, 6 and 7). LOD allowed tracing of the target drug at a nano-molar level down to 210 nM. GEMI was successfully determined in pharmaceutical formulations and different water samples without any pretreatment steps with satisfactory recovery (96.93–105.28% with SD values < 3). All sensors revealed a long lifetime of up to several months and are considered promising tools for monitoring water quality and efficiency of water treatment measures.
1 November 2021 in Journal of the Electrochemical Society
A green voltammetric method of analysis is proposed for the electrochemical determination of 3,5-di-tert-butyl-4-hydroxybenzoic acid (BHTCOOH); the major metabolite of the extensively consumed antioxidant, butylated hydroxytoluene (BHT). Environmental contamination by BHTCOOH is unavoidable owing to recurrence human exposure for these chemicals so (BHTCOOH) was detected in human urine and Nile River water samples. BHTCOOH is investigated by applying square-wave voltammetry (SWV) at two in-house fabricated screen-printed electrodes (SPE); Screen-Printed Graphite Electrode (SPGE) and Graphene-Modified Screen-Printed Graphite Electrode (GM-SPGE). Cyclic voltammetric analysis is used to optimize the voltammetric conditions. BHTCOOH oxidation on the surface of the electrodes is found to be irreversible and diffusion controlled. Using our fabricated SPEs, a linearity range of 4.88–21.62 and 0.12–1.31 μ g ml −1 with minimum detectability levels of 1.06 and 0.03 μ g ml −1 are reached at the surface of the SPGE and GM-SPGE, respectively. Moreover, the greenness of the method is inspected and found to be “excellent,” owing to the use of limited amounts of less hazardous chemicals and hence reduced waste production. The developed method is then successfully applied on urine and Nile-River samples; being the major source of water in Egypt, thereby allow for an adequate assessment of risks to human health and safety.
Nanotopographic surfaces are a powerful tool for studying and controlling cell behavior. However, the fabrication of nanotopographic master patterns using conventional photolithography is expensive, which limits the range of designs that can be explored. In this study, a method is demonstrated for the photoreshaping of large‐area patterns of nanoridges. The original master pattern is created using conventional lithography, and an azopolymer replica is prepared using soft lithography. The manipulation of the nanoridges is achieved by projecting light with specific polarizations and exposure times, resulting in controllable widening, buckling, or removal of the ridges. The reprogrammed azopolymer master patterns can then be replicated, creating reproducible new nanotopographies that can be transferred into other materials using a molding procedure. Diffraction can be used for in situ monitoring of the reprogramming during exposure. Image‐analysis methods are used to characterize buckled ridges as a function of exposure time. The response of MCF10A epithelial cells are investigated to buckled nanoridges. A substantial impact of buckling on the dynamics and location of actin polymerization, as well as on the distribution and lengths of contiguous polymerized regions is also observed.