The aim of this study is to obtain a systematic insight into the scandium (Sc) concentration dependence of the spontaneous polarization (Psp) in ScxAl1−xN by using first-principles calculations. From the calculated results, we observe that a structural change from a c-axis polarized wurtzite structure to a nonpolarized layered hexagonal structure takes place at x = 0.67, and the spontaneous polarization decreases nonlinearly with a change in the Sc concentration. Furthermore, we calculate the spontaneous polarizations from each cation individually and find that the spontaneous polarization from aluminum–nitrogen (Al–N) ( ) is higher than that from scandium–nitrogen (Sc–N) ( ). This difference in spontaneous polarization arising from the cationic origin is attributed to the difference in the internal parameter along the c axis ( ) based on the layered hexagonal structure.
The enhancement mechanism of piezoelectric properties by codoping Mg + X (X = Nb, Ti, Zr, Hf) into aluminum nitride (AlN) was investigated by first-principles calculations. Theoretically, the piezoelectric constant (d33) can be increased when the elastic constant (C33) is decreased and the piezoelectric stress constant (e33) is increased. All components of e33, which consists of the clamped e33, the Born effective charge (Z33), and the strain sensitivity (du/dε) of the internal parameter, were improved by the addition of Mg + X into AlN. The decrease in C33 and the increase in du/dε that were observed in Mg + X-codoped AlN indicate the occurrence of elastic softening which was considered to be influenced by changes in the interatomic bond in the wurtzite structure. The bonding analysis of metal–nitrogen (Me–N) pairs in the Mg + X-codoped AlN system which was carried out by crystal orbital Hamilton populations showed that the covalent bonding (Me–N) was weaker than in pure AlN. Therefore, this weaker covalent bond is considered to be one of the origins of the elastic softening. Similar phenomena were also found for Sc-doped AlN which has higher piezoelectric response than that of pure AlN.
Polarity is among the critical characteristics that could governs the functionality of piezoelectric materials. In this study, the polarity of aluminum nitride (AlN) thin films was inverted from Al-polar to N-polar by doping Si into AlN in the range of 1–15 at.%. Polarity inversion from Al-polar to N-polar also occurred when MgSi was codoped into AlN with Mg to Si ratio was less than 1. However, the polarity can be reversed from N-polar to Al-polar when the ratio of Mg and Si was greater than 1. The effect of Si and MgSi addition was investigated with regards to their crystal structure, lattice parameters, polarity distribution and the oxidation state of each elements. Furthermore, the effect of intermediate layer as well as the presence of point defect (i.e. aluminum vacancy) were investigated and how these factors influence the polarity of the thin films are discussed in this report.
1 September 2015 in Journal of Alloys and Compounds
This study employs first-principles calculations to investigate how introducing Yb into aluminum nitride (AlN) leads to a large enhancement in the material’s piezoelectric response (d33). The maximum d33 is calculated to be over 100 pC/N, which is 20 times higher than that of AlN. One reason for such a significant improvement in d33 is the elastic-softening effect, which is indicated by a decrease in the elastic constant, C33. The strain sensitivity (du/dε) of the internal parameter, u, is also an important factor for improving the piezoelectric stress constant, e33. On the basis of mixing enthalpy calculations, YbxAl1−xN is predicted to be more stable as a wurtzite phase than as a rock salt phase at composition up to x ≈ 0.7. These results suggest that Yb can be doped into AlN at high concentrations. It was also observed that the dielectric constant, , generally increases with increasing Yb concentrations. However, the electromechanical coupling coefficient, , only increases up to x = 0.778, which is likely because of the relatively lower values of within this range.