A robust and reliable gas sensing device is considered as a convenient and practical solution for gas concentration monitoring that has become a mandatory requirement in different field of applications. For in situ hazardous gases detection, a mixed-potential type gas sensor has been regarded as a promising solid-state gas sensor. For the past three decades, there has been a significant progress in achieving high performance in mixed-potential type sensors. Therefore, this review is focused on reporting the development of mixed-potential type gas sensors with combined yttria-stabilized zirconia (YSZ) as the base solid electrolyte material and various classes of electrode materials for their potential utilization as a high-performance sensing electrode. The underlying sensing mechanism of a mixed-potential type YSZ-based sensor is elaborated here in detail. Transformation in design and configuration of this type of sensor is also covered in this report. In addition, recent progresses on mixed-potential type gas sensors development for detection of several target gases, such as carbon monoxide, hydrocarbons, nitrogen oxides, hydrogen, and ammonia, are reviewed. Strategies to improve the sensing characteristic, particularly gas sensitivity and selectivity, are also reported. Based on the understanding of the fundamental sensing mechanism and the requirements for high-performance gas sensors, challenges and future trends for this type of gas sensor development are discussed.
The aim of this study is to obtain a systematic insight into the scandium (Sc) concentration dependence of the spontaneous polarization (Psp) in ScxAl1−xN by using first-principles calculations. From the calculated results, we observe that a structural change from a c-axis polarized wurtzite structure to a nonpolarized layered hexagonal structure takes place at x = 0.67, and the spontaneous polarization decreases nonlinearly with a change in the Sc concentration. Furthermore, we calculate the spontaneous polarizations from each cation individually and find that the spontaneous polarization from aluminum–nitrogen (Al–N) ( ) is higher than that from scandium–nitrogen (Sc–N) ( ). This difference in spontaneous polarization arising from the cationic origin is attributed to the difference in the internal parameter along the c axis ( ) based on the layered hexagonal structure.
The enhancement mechanism of piezoelectric properties by codoping Mg + X (X = Nb, Ti, Zr, Hf) into aluminum nitride (AlN) was investigated by first-principles calculations. Theoretically, the piezoelectric constant (d33) can be increased when the elastic constant (C33) is decreased and the piezoelectric stress constant (e33) is increased. All components of e33, which consists of the clamped e33, the Born effective charge (Z33), and the strain sensitivity (du/dε) of the internal parameter, were improved by the addition of Mg + X into AlN. The decrease in C33 and the increase in du/dε that were observed in Mg + X-codoped AlN indicate the occurrence of elastic softening which was considered to be influenced by changes in the interatomic bond in the wurtzite structure. The bonding analysis of metal–nitrogen (Me–N) pairs in the Mg + X-codoped AlN system which was carried out by crystal orbital Hamilton populations showed that the covalent bonding (Me–N) was weaker than in pure AlN. Therefore, this weaker covalent bond is considered to be one of the origins of the elastic softening. Similar phenomena were also found for Sc-doped AlN which has higher piezoelectric response than that of pure AlN.
Polarity is among the critical characteristics that could governs the functionality of piezoelectric materials. In this study, the polarity of aluminum nitride (AlN) thin films was inverted from Al-polar to N-polar by doping Si into AlN in the range of 1–15 at.%. Polarity inversion from Al-polar to N-polar also occurred when MgSi was codoped into AlN with Mg to Si ratio was less than 1. However, the polarity can be reversed from N-polar to Al-polar when the ratio of Mg and Si was greater than 1. The effect of Si and MgSi addition was investigated with regards to their crystal structure, lattice parameters, polarity distribution and the oxidation state of each elements. Furthermore, the effect of intermediate layer as well as the presence of point defect (i.e. aluminum vacancy) were investigated and how these factors influence the polarity of the thin films are discussed in this report.
1 December 2011 in Sensors and Actuators B: Chemical