In order to synthesize a new kind of buoyancy material with high-strength, low-density and low-water-absorption and to study the curing reaction of tetraglycidylamine epoxy resin with an aromatic amine curing agent, the non-isothermal differential scanning calorimeter (DSC) method is used to calculate the curing kinetics parameters of N,N,N′,N′-tetraepoxypropyl-4,4′-diaminodiphenylmethane epoxy resin (AG-80) and the m-xylylenediamine (m-XDA) curing process. Further, buoyancy materials with different volume fractions of hollow glass microsphere (HGM) compounded with a AG-80 epoxy resin matrix were prepared and characterized. The curing kinetics calculation results show that, for the curing reaction of the AG-80/m-XDA system, the apparent activation energy increases with the conversion rates increasing and the reaction model is the Jander equation (three-dimensional diffusion, 3D, n = 1/2). The experimental results show that the density, compressive strength, saturated water absorption and water absorption rate of the composite with 55 v % HGM are 0.668 g·cm−3, 107.07 MPa, 0.17% and 0.025 h−1/2, respectively. This kind of composite can probably be used as a deep-sea buoyancy material.
The main problem for the application of hydrogen generated via hydrolysis of metal alloys is the low hydrogen generation rate (HGR). In this paper, active Al alloys were prepared using a new coupled method-melting-mechanical crushing-mechanical ball milling method to enhance the HGR at room temperature. This method contains three steps, including the melting of Al, Ga, In, and Sn ingots with low melting alloy blocks and casting into plates, then crushing alloy plate into powders and ball milling with chloride salts such as NiCl2 and CoCl2 were added during the ball milling process. The microstructure and phase compositions of Al alloys and reaction products were investigated via X-ray diffraction and scanning electron microscopy with energy dispersed X-ray spectroscopy. The low-melting-point Ga-In -Sn (GIS) phases contain a large amount of Al can act as a transmission medium for Al, which improves the diffusion of Al to Al/H2O reaction sites. Finer GIS phases after ball milling can further enhance the diffusion of Al and thus enhance the activity of Al alloy. The hydrogen generation performance through hydrolysis of water with Al at room temperature was investigated. The results show that the H2 generation performance of the Al-low-melting point alloy composite powder is significantly higher than the results reported to date. The highest H2 generation rate and H2 conversion efficiency can reach 5337 mL·min−1·g−1 for the hydrolysis of water with 1 g active alloy.
In recent years, time of flight-secondary ion mass spectrometer (ToF-SIMS) has been widely employed to acquire surface information of materials. Here, we investigated the alloy surface by combining the mass spectra and 2D mapping images of ToF-SIMS. We found by surprise that these two results seem to be inconsistent with each other. Therefore, other surface characteristic tools such as SEM-EDS were further used to provide additional supports. The results indicated that such differences may originate from the variance of secondary ion yields, which might be affected by crystal orientation.
High hydro-active Al-3Ga-3In-3Sn alloys were prepared by coupling alloying and mechanical milling methods. NiCl2 was added to the alloy during ball milling as the catalyst. XRD, SEM, and XAFS were used for the characterization of the hydro-active alloy. The hydrogen generation properties were systematically investigated in tap water at room temperature. The results show that the hydrogen generation rate is 11.02 L∙min−1∙g−1, and the conversion yield is 90.25% for the Al-3Ga-3In-3Sn-2NiCl2 composite with a ball milling time of 2 h at room temperature in tap water. The hydrolysis reaction contains the expansion of the Al-based phase into a nano-sized layer and the further hydrolysis reaction of the layered Al phase with water. The activation mechanism was also investigated, and the activation of Al was attributed to the Al-Ni galvanic with the existing Cl−, which leads to a faster hydrolysis reaction rate for ball-milled powder with NiCl2.
Aluminum powder plays important role in the field of energetic materials. However, it is often vulnerable to oxygen and water due to the high reactivity of aluminum, and it is challenging to build up uniform and passivated coating via existing means. In this work, (Heptadecafluoro-1,1,2,2-tetradecyl) trimethoxysilane (FAS-17) and glycidyl azide polymer (GAP) were used to coat the surface of high water-reactive aluminum powder (w-Al) to form inactivated w-Al@FAS-17@GAP energetic materials, via the synergy of chemical bonding and physical attraction. Thermal reaction tests showed that the exothermic enthalpy of w-Al@FAS-17@GAP was 5.26 times that of w-Al. Ignition tests showed that w-Al@FAS-17@GAP burnt violently at 760 °C, while w-Al could not be ignited even at 950 °C. In addition, the combined coating of FAS-17 and GAP could effectively improve the hydrophobicity and long-term stability of w-Al, which helped to overcome the poor compatibility of w-Al with explosive components. Our work not only displayed an effective routine to synthesize O2/H2O proof Al energetic materials, but also pointed out a synergistically chemical and physical strategy for constructing intact high-performance surfaces.