This study concerns the modeling of the hysteretic behavior of magnetorheological (MR) dampers. In general, hysteresis is one of key factors influencing the output of such actuators. So far, more attention has been paid to studying the combined hysteretic behavior of MR actuators by observing the relationships between the output (force/torque) and the inputs (current, velocity, and position). However, these devices feature two distinct hysteretic mechanisms: mechanical/hydraulic and magnetic. The mechanical hysteresis is of different nature than the magnetic hysteresis due to the properties of ferromagnetic materials forming the actuator's electromagnet circuit, and these should be split in the modeling process. In the present study, we separate the magnetic hysteresis from the mechanical/hydraulic one by investigating the magnetic flux vs. exciting current relationship of a commercial flow-mode MR damper subjected to sinusoidal current loading and independently of the mechanical excitations. The resulting behavior of the electromagnetic circuit is then examined using the non-linear inductor approach with hysteresis. Total hysteresis is then modeled using a non-linear inductor model in combination with a phenomenological parametric Maxwell type model of the damper.
Magnetorheological (MR) dampers are well‐known devices based on smart fluids. The dampers exhibit nonlinear hysteretic behaviour which affects their performance in control systems. Hence, an effective control scheme must include a hysteresis compensator. The source of hysteresis in MR dampers is twofold. First, it is due to the compressibility and inertia of the fluid. Second, magnetic hysteresis is the inherent property of ferromagnetic materials that form the control circuit of the valve including MR fluid. While the former was studied extensively over the past years using various phenomenological models, the latter has attracted less attention. In this paper, we analyze the magnetic hysteretic behaviour of three different MR dampers by investigating their current‐flux relationships. Two dampers operate in flow mode, whereas the third one is a shear‐mode device (brake). The approach is demonstrated using a sensorless magnetic flux estimation technique. We reveal the response of the dampers when subjected to sinusoidal inputs across a wide range of operating conditions and excitation inputs. Our observations of the flux data showed that the hysteresis is influenced by both amplitude and the frequency of the excitation input. The procedure allows to analyze the magnetic hysteresis independently of other sources of hysteresis in MR dampers; on this basis, more effective damper models and control algorithms can be developed in the future.
The aim of the work is to investigate power flows in the vibration reduction system equipped with a magnetorheological (MR) damper and energy regeneration. For this purpose, experiments were conducted in the test rig compound of the shaker and the vibration reduction system (electromagnetic harvester, MR damper, spring) which are attached to the sprung mass. The experimental data acquired under sine excitations enabled us to analyze instantaneous power fluxes, as well as a rate of inertial energy changes in the system.
The work deals with a newly developed prototype of an electrical control unit (ECU) for a magnetorheological (MR) damper powered by energy harvested from vibrations. The ECU, consisting of a rectifying bridge, a driver unit, a microcontroller, and an internal power supply system, is an advanced version of the specially designed processing system for energy harvested from vibrations and the use of this energy to control the MR damper. Unlike a typical MR damper control system in which electrical circuits are powered from an external energy source, the ECU is powered by a part of the energy extracted from a vibrating system using an electromagnetic harvester. However, the excess amount of energy recovered over that necessary to power the MR damper and electrical circuits can be collected in harvested energy storage. The study presents the design concept of the ECU, computer simulations of the in-built driver unit (DU), the method of connecting the ECU with the harvester, the MR damper and displacement sensors, and also describes experimental tests of the engineered unit applied in a vibration reduction system (VRS) with an energy recovery function.
7 May 2017 in Journal of Intelligent Material Systems and Structures
Magnetorheological dampers have been useful tools in research and real-life projects in areas related to vibration damping and vibration isolation. At the same time, research data indicate that their transient performance is influenced by electromagnetic circuit characteristics, driving electronics, control approach, and fluid’s own dynamics. When compared to standard flow mode (valve mode), device squeeze-mode magnetorheological hardware featuring a control gap of varying height according to prescribed force or displacement is further complicated by both complex dynamics of the fluid flow and the electromagnetic circuit. As such, the primary purpose of this article is to provide an outlook on dynamic aspects of magnetorheological dampers operating in squeeze mode. In this study, the authors examined the transient behavior of a prototype damper subjected to mechanical and electrical stimuli. In particular, the work includes a comparison of the experimental results obtained for a damper subjected to voltage step inputs (open loop) and controlled inputs (closed loop), respectively. An attempt to extract magnetic flux data was performed, too. The results show that a proportional–integral–derivative controller allows for accelerating the current response time of the squeeze-mode actuator. However, observations of the flux preliminary data indicate that the transient performance of the device actuator is severely influenced by both piston position (control gap height) and current in the control coil. The results reveal that the electromagnetic circuit response is a major contributor to the actuator’s dynamics and a particular care needs to be undertaken in future projects to design an efficient magnetorheological squeeze-mode damper system.