Transient behavior of a magnetorheological brake excited by step currents under compression-shear mode has been experimentally studied. The results show that the amplitude of the applied current had little effect on the rising time of transient torque, while the rising time was significantly affected by the rotational speed, the compressive speed and the compressive strain position. The falling time of transient torque was independent of the amplitude of the applied current, the compressive speed and the compressive strain position, and it was affected by the rotational speed. The falling time of the transient torque was much shorter than the rising time by a step current. The transient process of MR brake applied as a step current was different from a stable process pre-applied at constant current in different particle chain structure forming processes. In addition, the compressive processes applied in one step current and randomly on/off current were compared and experimentally verified: the particle chains in two processes both experienced the same evolutionary of transient torque. The results achieved in this study should be properly considered in the design and control of magnetorheological brake under compression-shear mode.
Compressions of magnetorheological (MR) fluids have been carried out under instantaneous magnetic fields. The yield strength of the MR fluid in compressive mode has been derived by assuming that it was a transformed shear flow in Bi-visous model. The compressive stresses have experimentally studied under different magnetic fields, different initial gap distances and different compressive velocities. The nominal yield shear stresses of the compressed MR fluid under different influential factors have been calculated. The compressive stress increased in a power law as the applied magnetic field increased, while it decreased as the initial gap distance and the compressive velocity increased. With the increase of magnetic field, the difference between the nominal yield shear stress curves increased, and the exponents of the power law increased with the increase of the magnetic field strengths. A larger initial gap distance and a lower compressive velocity resulted in a higher nominal yield shear stress under the same instantaneous magnetic field. The achieved results of the nominal yield shear stress with magnetic field seemed to deviate from the prediction of dipole model, and the chain structure aggregation effect, the sealing effect and the friction effect by compression should be considered.
The compression tests under the unidirection for magnetorheological (MR) fluids have been studied at different compressive speeds. The results indicated that curves of compressive stress under different compression speeds at the applied magnetic field of 0.15 T overlapped well and were shown to be an exponent of about 1 of the initial gap distance in the elastic deformation region and accorded well with the description of continuous media theory. The difference in compressive stress curves increases significantly with an increasing magnetic field. At this time, the continuous media theory description could not be accounted for the effect of compressive speed on the compression of MR fluid, which seems to deviate from the Deborah number prediction under the lower compressive speeds. An explanation based on the two-phase flow due to aggregations of particle chains resulting in much longer relaxation times at a lower compressive speed was proposed to explain this deviation. The results have guiding significance for the theoretical design and process parameter optimization for the squeeze-assisted MR devices such as MR dampers and MR clutches based on the compressive resistance.
In view of the problem that special gondola cars are generally insufficient for the actual transportation of coke, and in order to improve the transportation efficiency and reduce the transportation cost, the 80 t depressed-center gondola car for coke transportation is designed by the anti-fatigue design method in this paper. The car body with a supporting bar and the car body without a supporting bar are simulated and analyzed by the finite element method; the results show that there are stress mutations at the transition area of the two key welds, especially at the 110 mm of weld 1. The fatigue lives of the two car body schemes are evaluated by Miner linear cumulative damage theory, spectrum and S-N curve in AAR standard, and load spectrum of the Daqin line and S-N curve in BSI standard. The results show that the 80 t depressed-center gondola car body with a supporting bar is the best scheme. In addition, the fatigue damage results show that the vertical load spectrum of AAR is worse than that of the Daqin line, and the longitudinal load spectrum of the Daqin line is worse than that of AAR. This conclusion will provide a basis for an anti-fatigue design of heavy haul wagon bodies or bogies.
Unidirectional compressive properties of magnetorheological (MR) fluids have been investigated under slow compression and constant area with different magnetic fields and different initial gap distances. Experimental tests of unidirectional compression were firstly carried out by using a commercial plate–plate rheometer. The theoretical model based on the continuous squeeze flow theory was developed to calculate the compressive stress. The comparisons between the measured and calculated compressive stresses of MR fluids were made. It showed that the compression resistance of the MR fluid in the magnetic field was much higher than that predicted by the theory. With the increasing magnetic flux density, the deviation between measured and calculated curves accelerated. Characteristics of the compressive stress variation with the reduction in gap distance have been analyzed. The structure strengthening effect induced by the chain structure aggregation in squeeze mode has been used to explain this deviation.
In order to find out the root cause of cross bearer welds’ cracks in general-purpose gondola cars, the relationship between asymmetric structure and stress distribution is studied in this paper. Firstly, the concept of asymmetry coefficient and stress distribution cluster is proposed, and the asymmetric coefficients’ calculation methods of independent and dependent variables are given, respectively, in two-dimensional space. Secondly, according to the different positions of side column 1 and side column 2, 30 local models are established, the cross bearer weld stresses are extracted after finite element simulation, and the stress distribution clusters of cross bearer weld stresses are formed. Finally, the asymmetry coefficients of the side columns are calculated, and the correlation between the positions of the side columns and the weld stresses is studied using the methods of Pearson correlation coefficient and complex correlation coefficient. The results show that the correlation between the stress of cross bearer weld 2 and the positions of the side columns is much higher than that between the stress of cross bearer weld 1 and the positions of the side columns. Meanwhile, it shows that the method presented in this paper is feasible and effective for the analysis and research of asymmetric structures. These combined with the calculation method of the correlation coefficient.