JIRI MARSALEK

Prof. JIRI MARSALEK


Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

1 March 2018 in Journal of Cold Regions Engineering
Verified
Journal Article
Closed access
SMShahab Moghadas
Shahab Moghadas
GLGünther Leonhardt
Günther Leonhardt
JMJIRI MARSALEK
JIRI MARSALEK
Maria ViklanderMaria Viklander
Maria Viklander
A methodological study of modeling runoff from rain-on-snow events was conducted using the northern Swedish city of Kiruna as a test case, with respect to physiographic, drainage system, and the current and projected future climate data. Runoff simulations were carried out with the PCSWMM, which is a geographic information system (GIS) supported version of the U.S. EPA Storm Water Management Model (U.S. EPA SWMM5) developed by Computational Hydraulics International (CHI). In total, 177 simulations were run covering four scenario categories: eight rain events, three climates (the current and two projected), three soil infiltration rates, and five snow water equivalent (SWE) values. Simulation results were analyzed with respect to influential rainfall/snowmelt/runoff factors and the noted differences were statistically tested for significance. Result analysis revealed new findings concerning the differences between runoff generated by rain-on-snow and summer thunderstorm events. In particular, it was noted that a relatively frequent rain-on-snow event, with a return period of 1.4 year, caused fewer flooded nodes and surcharged pipes in the catchment sewer system, but almost five times greater runoff volume, when compared to the same drainage system performance indicators corresponding to a 10-year event occurring in the summer. Depending on the physical characteristics of the snow cover, among which the depth appears the most important, rainwater and snowmelt may be retained in, or released from, the snowpack, which acts as a dynamic reservoir controlling the generation and release of runoff. Smaller snow depths produce smaller volumes of melt, smaller storage capacity and less effective insulation of soils, which may freeze to greater depths and become practically impervious, until the process of soil thawing has been completed. The impacts of climate change in the study area, described by increases in precipitation and air temperatures, are likely to cause more frequent runoff problems attributed to the future rain-on-snow events. Even though the runoff tendencies reported here reflect the characteristics of the study area and climate, they suggest the need to consider rain-on-snow events in sewer design and storm water management in regions with seasonal snow covers, certainly with respect to runoff volumes.

1 June 2017 in Journal of Environmental Engineering
Verified
Journal Article
Closed access
AAAhmed Al-Rubaei
Ahmed Al-Rubaei
LMLaura S. Merriman
Laura S. Merriman
WHWilliam F. Hunt
William F. Hunt
Maria ViklanderMaria Viklander
Maria Viklander
JMJIRI MARSALEK
JIRI MARSALEK
GBGodecke-Tobias Blecken
Godecke-Tobias Blecken
During the past 50 years, wet stormwater ponds have been constructed to reduce negative environmental impacts of urban stormwater discharges on receiving aquatic environments. However, in many jurisdictions there is little information on the current operational status of such ponds and their functioning. This paucity of information prompted a field survey of 25 Swedish municipal stormwater ponds, aged between 3 and 26 years. The pond survey focused on estimating the pond hydraulic loading and efficiency, the state of littoral vegetation, characteristics of bottom sediment in the inlet and outlet zones (sizes and the chemistry), and the overall operational pond status, including the access for maintenance. The hydraulic efficiencies of ponds were estimated for pond footprint shapes and relative locations of the inlets and outlets using literature data. The estimated hydraulic efficiencies correlated well with the pond length-to-width ratios and the ratio of the pond surface area to the impervious area of the runoff contributing catchment (i.e., the hydraulic loading). Littoral vegetation was inspected visually and found to be overgrown at some facilities, which impeded the maintenance access. Benthic sediments in ponds contained silt and clay (<63  μm ), sand and gravel fractions, and when compared with the literature data, such sediments appeared relatively coarse. Chemical characteristics of sediments reflected anthropogenic (traffic) activities, but without excessive contamination warranting special disposal requirements. Of the 25 ponds surveyed, four were fenced off and inaccessible to machinery. In fact, the design of these four ponds was such that it made inspection and maintenance very difficult, which may pose potential risks to ponds operation. Fifty-four percent of the investigated ponds were in need of minor maintenance, primarily because of sediment and litter accumulation in their inflow and outflow sections. The fact that the inspection survey revealed relatively few minor issues that could be corrected easily demonstrates the importance of relatively simple regular inspections serving to detect minor problems at an early stage before they would seriously impact pond functioning. The above survey methodology should be helpful for developing similar low-cost surveys in other jurisdictions.

1 December 2021 in Journal of Environmental Management
Verified
Journal Article
Open access
AMAlexandra Müller
Alexandra Müller
HÖHeléne Österlund
Heléne Österlund
JMJIRI MARSALEK
JIRI MARSALEK
Maria ViklanderMaria Viklander
Maria Viklander
Runoff from building and structure surfaces may contribute to the pollution of urban stormwater and, thereby, to the degradation of the receiving water quality. Various micropollutants have been found in surface runoff from buildings in the urban environment, including metals and organic micropollutants. Effective methods for identification of such pollutants and their sources are the prerequisites for the development of control measures. In this paper, three different methods for the identification of building surface materials acting as sources of metals (Cd, Cr, Cu, Ni, Pb and Zn), nonylphenols and phthalates are presented: (i) screening of the material composition, (ii) laboratory leaching experiments with synthetic rainwater, and (iii) open-air pilot testing of material panels exposed to actual rainfall and runoff. These three methods cover a wide span of experimental aspects, including, e.g., size of material samples, resource demands, and control of influential factors. Nine materials commonly used on building and structure surfaces in the urban environment were tested: metal sheets of zinc, copper, galvanised steel, coated corrugated steel and stainless steel; and, four different roofing membranes of bitumen as well as polyvinyl chloride (PVC). The experimental results indicated that all three methods were meritorious in providing some information contributing to the identification of pollutant sources. The screening of material composition for targeted pollutants is relatively quick and inexpensive, but may fail to identify minor sources of pollutants, or may identify the substances present in the material, but not released in contact with water. Laboratory leaching was generally effective in identifying sources of substances present in surface runoff, but was unsuitable for estimating the magnitude of actual concentrations in building runoff. Open-air pilot studies of material samples (exposed area = 2 m2) were thought to provide the results corresponding well to concentrations in runoff from actual building surfaces, but required relatively large financial and labour resources. Thus, the choice of the method for pollutant identification should be based on study objectives, and some benefits may be achieved using more than one method in an integrated manner; e.g., composition screening and lab or open-air leaching of targeted materials.

27 December 2020 in Water
Verified
Journal Article
Open access
PDF file
HÅHans O Åkerstedt
Hans O Åkerstedt
Staffan LundströmStaffan Lundström
Staffan Lundström
SLSofia of Larsson
Sofia of Larsson
JMJIRI MARSALEK
JIRI MARSALEK
Maria ViklanderMaria Viklander
Maria Viklander
The swelling effect in hydrogel bodies or sponge-like porous bodies (SPB) used in a specific stormwater storage concept of the down-flow type is considered. A macroscopic swelling model is proposed, in which water is assumed to penetrate into the hydrogel by diffusion described by diffusion equations together with a free-moving boundary separating the interface between the water and hydrogel. Such a type of problem belongs to the certain class of problems called Stefan-problems. The main objective of this contribution is to compare how the theoretical total amount of absorbed water is modified by the inclusion of swelling, when compared to the previously studied SPB devices analyzed only for the effect of diffusion. The results can be summarized in terms of the geometrical dimensions of the storage device and the magnitude of the diffusion coefficient D. The geometrical variables influence both the maximum possible absorbed volume and the time to reach that volume. The diffusion coefficient D only influences the rate of volume growth and the time to reach the maximum volume of stored water. The initial swelling of the hydrogel SPB grows with time (Dt) until the steady state is reached and the swelling rate approaches zero. In all the cases considered, the swelling in general increases the maximum possible absorbed water volume by an amount of 14%.

2 March 2022 in Sustainability
Verified
Journal Article
Open access
PDF file
TLThomas Larm
Thomas Larm
AWAnna Wahlsten
Anna Wahlsten
JMJIRI MARSALEK
JIRI MARSALEK
Maria ViklanderMaria Viklander
Maria Viklander
The StormTac Web model, representing a low-complexity conceptual model (LCCM), was applied to two urban catchments featuring stormwater quality controls, a stormwater pond or a biofilter. The model calculates annual average runoff from annual precipitation and land-use specific volumetric runoff coefficients and baseflows (in storm sewers), which are multiplied by the corresponding mean stormwater quality constituent concentrations obtained from the recently upgraded StormTac Database, to yield constituent loads. The resulting runoff loads pass through the stormwater quality control facilities (a stormwater pond or a biofilter) where treatment takes place and its efficacy is described by “reduction efficiencies”. For the four selected stormwater quality constituents (TP, Cu, Zn, TSS) and two study catchments, a 201-ha residential Ladbrodammen and an 8.2-ha Sundsvall traffic corridor, the compositions of stormwater entering and leaving the control facilities were calculated by StormTac Web and compared against the measured data. In general, the calculated concentrations were smaller than the measured ones, and these differences were reduced, but not eliminated in all cases, by considering uncertainties in both calculated and measured data. Uncertainties in calculated values consisted of two components, a flow component (assumed as 20%) and a concentration component, which was assumed equal to the relative standard error (RSE) of the data in the StormTac Database. Explanations of differences in calculated and measured stormwater data were discussed with respect to temporal changes and trends in environmental practices and stormwater quality monitoring and enhancement by treatment.