Gaurang Vakil

Dr. Gaurang Vakil

Power Electronics, Machines and Control Group, University of Nottingham, Nottingham, UK
orcid

Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2016 in IET Electric Power Applications
Verified
Journal Article
Open access
PDF file
RARobert Abebe
Robert Abebe
GVGaurang Vakil
Gaurang Vakil
GCGiovanni Lo Calzo
Giovanni Lo Calzo
TCThomas Cox
Thomas Cox
SLSimon Lambert
Simon Lambert
BMBarrie Mecrow
Barrie Mecrow
With increased need for high power density, high efficiency and high temperature capabilities in aerospace and automotive applications, integrated motor drives (IMD) offers a potential solution. However, close physical integration of the converter and the machine may also lead to an increase in components temperature. This requires careful mechanical, structural and thermal analysis; and design of the IMD system. This study reviews existing IMD technologies and their thermal effects on the IMD system. The effects of the power electronics position on the IMD system and its respective thermal management concepts are also investigated. The challenges faced in designing and manufacturing of an IMD along with the mechanical and structural impacts of close physical integration is also discussed and potential solutions are provided. Potential converter topologies for an IMD like the matrix converter, two‐level bridge, three‐level neutral point clamped and multiphase full bridge converters are also reviewed. Wide band gap devices like silicon carbide and gallium nitride and their packaging in power modules for IMDs are also discussed. Power modules components and packaging technologies are also presented.

18 July 2016 in IEEE Transactions on Transportation Electrification
Verified
Journal Article
Closed access
PAPuvan Arumugam
Puvan Arumugam
ZXZeyuan Xu
Zeyuan Xu
ARAntonino La Rocca
Antonino La Rocca
GVGaurang Vakil
Gaurang Vakil
MDMatthew Dickinson
Matthew Dickinson
SPStephen J. Pickering
Stephen J. Pickering
This paper proposes a novel solid rotor topology for an interior permanent magnet (IPM) machine, adopted in this case for an aircraft starter-generator design. The key challenge in the design is to satisfy two operating conditions that are a high torque at start and a high speed at cruise. Conventional IPM topologies that are highly capable of extended field weakening are found to be limited at high speed due to structural constraints associated with the rotor material. To adopt the IPM concept for high-speed operation, it is proposed to adopt a rotor constructed from semimagnetic stainless steel, which has a higher yield strength than laminated silicon steel. To maintain minimal stress levels and also minimize the resultant eddy current losses due to the lack of laminations, different approaches are considered and studied. Finally, to achieve a better tradeoff between the structural and electromagnetic constraints, a novel slitted approach is implemented on the rotor. The proposed rotor topology is verified using electromagnetic, static structural, and dynamic structural finite-element analyses. An experiment is performed to confirm the feasibility of the proposed rotor. It is shown that the proposed solid rotor concept for an IPM fulfils the design requirements while satisfying the structural, thermal, and magnetic limitations.

13 December 2021 in Energies
Verified
Journal Article
Open access
PDF file
LTLiya Tom
Liya Tom
MKMuhammad Raza Khowja
Muhammad Raza Khowja
GVGaurang Vakil
Gaurang Vakil
CGChristopher Gerada
Christopher Gerada
Electric and hybrid-electric aircraft propulsion are rapidly revolutionising mobility technologies. Air travel has become a major focus point with respect to reducing greenhouse gas emissions. The electrification of aircraft components can bring several benefits such as reduced mass, environmental impact, fuel consumption, increased reliability and quicker failure resolution. Propulsion, actuation and power generation are the three key areas of focus in more electric aircraft technologies, due to the increasing demand for power-dense, efficient and fault-tolerant flight components. The necessity of having environmentally friendly aircraft systems has promoted the aerospace industry to use electrically powered drive systems, rather than the conventional mechanical, pneumatic or hydraulic systems. In this context, this paper reviews the current state of art and future advances in more electric technologies, in conjunction with a number of industrially relevant discussions. In this study, a permanent magnet motor was identified as the most efficient machine for aircraft subsystems. It is found to be 78% and 60% more power dense than switch-reluctant and induction machines. Several development methods to close the gap between existing and future design were also analysed, including the embedded cooling system, high-thermal-conductivity insulation materials, thin-gauge and high-strength electrical steel and integrated motor drive topology.

7 July 2016 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
NFNuwantha Fernando
Nuwantha Fernando
GVGaurang Vakil
Gaurang Vakil
PAPuvan Arumugam
Puvan Arumugam
EAEmmanuel Amankwah
Emmanuel Amankwah
CGChristopher Gerada
Christopher Gerada
SBSerhiy Bozhko
Serhiy Bozhko
This paper investigates the effect of two soft magnetic materials on a high-speed machine design, namely, 6.5% silicon steel and cobalt-iron alloy. The effect of design parameters on the machine performance as an aircraft starter-generator is analyzed. The material properties which include B-H characteristics and the losses are obtained at different frequencies under an experiment and used to predict the machine performance accurately. In the investigation presented in this paper, it is shown that machines designed with 6.5% silicon steel at a high core flux density has lower weight and lower losses than the cobalt-iron alloy designs. This is mainly due to the extra weight contributed by the copper content especially in the end-windings. Due to the high operating frequencies, the core losses in the cobalt-iron machine designs are found to outweigh the copper losses incurred in the silicon steel machines. It is also shown that change in stack length/number of turns has a considerable effect on the copper losses at starting, however has no significant advantage on rated efficiency which happens to be in a field-weakening operating point. It is also shown that the performance of the machine designs depends significantly on material selection and the operating point of the core. The implications of the variation of design parameters on the machine performance is discussed and provide insight into the influence of parameters that effect overall power density.

19 February 2018 in IEEE Transactions on Energy Conversion
Verified
Journal Article
Closed access
AAAhmed Al-Timimy
Ahmed Al-Timimy
GVGaurang Vakil
Gaurang Vakil
MDMichele Degano
Michele Degano
PGPaolo Giangrande
Paolo Giangrande
CGChristopher Gerada
Christopher Gerada
Michael GaleaMichael Galea
Michael Galea
An often-overlooked aspect during the development process of electrical machines is the validity and accuracy of the machine material properties being used at the design stage. Designers usually consider the data provided by the material supplier, which are measured on material in an unprocessed state. However, the fact that the machining processes required to produce the finished product (e.g., the stator core) can permanently vary the material properties is very often neglected. This paper, therefore, deals with and investigates the effects that such processes can have on the overall machine performance. To do this, three sets of material data, the material suppliers’ data, material data based on conventional characterization methods, and material data based on test samples that include the manufacturing processes, are used to develop three versions of the same baseline machine. The results of these three machines are then compared, and the resulting variations of the machine's performance are presented and described. The chosen baseline machine is a high-performance and relatively high speed, aerospace, electrical machine. Special attention is focused on the efficiency maps of the machine, as this aspect is highly dependent on the material properties that are the most sensitive to manufacturing processes such as the material's anhysteretic B–H curve and its specific core loss.

1 May 2024 in The Journal of the Acoustical Society of America
Verified
Journal Article
Open access
PDF file
Burak Buda TurhanBurak Buda Turhan
Burak Buda Turhan
Hasan Kamliya JawaharHasan Kamliya Jawahar
Hasan Kamliya Jawahar
AGAbhishek Gautam
Abhishek Gautam
SSShahjahan Syed
Shahjahan Syed
GVGaurang Vakil
Gaurang Vakil
MAMahdi Azarpeyvand
Mahdi Azarpeyvand
This experimental study investigates the effect of blade phase angle on noise attenuation in two adjacent, electronically synchronized propellers. Acoustic measurements were performed in an aeroacoustic wind tunnel with a distributed electric propulsion system that involved the adjustment of relative phase angles of 2-bladed propellers between Δψ = 0° and 90°. Ranges of advance ratios (J = 0–0.73) were investigated at a fixed propeller rotation speed of 5000 rpm. The investigation explored the impact on noise directivity and frequency characteristics. The findings reveal significant reductions in noise directivity and tonal noise at the blade pass frequency (BPF). A relative phase angle of Δψ = 90° demonstrated the maximum noise reduction, with an 8 dB decrease at the first BPF and a 2 dB reduction in overall sound pressure level at J = 0. For in-flow conditions (J > 0), a relative phase angle of Δψ = 90° resulted in significant noise reductions of about 24 dB in the first BPF and 6 dB in overall sound pressure level, compared to Δψ = 0°. These observations offer critical insights into the use of the propeller's relative phase angle as an effective noise control method in the distributed electric propulsion system.