The geometric complexity and high-pressure gradients that characterize the design of the flow field of gear pumps make it very difficult to obtain an accurate CFD simulation of the component. Usually, assumptions are made both in terms of geometrical features and physics being included in the analysis. The contact between the teeth, which is a key factor for the correct functioning of these pumps, represents a critical challenge in 3D CFD simulations, mainly due to the intrinsic limits of the dynamic meshing techniques that can hardly effectively manage a zero or close to zero gap point forming during gear rotation. The geometric complexity and high-pressure gradients that characterize the gear pump flow field make a CFD analysis quite difficult, and the contact between the gear teeth is usually avoided, thus being an extremely important feature. In this paper, a gear pump composed of inlet and outlet pipes was considered, and the contact between the gear’s teeth was modeled in two different ways, one where it is effectively implemented and one where it is avoided using distancing and a proper casing modification. Herein, a new methodology is proposed for the application of the dynamic mesh method in the Simcenter STAR-CCM+ environment using an adaptive remeshing technique. The proposed methodology is compared with the alternative overset meshing method available in the software. The new meshing method is implemented using a user-routing that reproduces the real geometry of the gears while rotating during the pump operation, with teeth contact included. The routine is optimized in order to limit the additional computation and time needed for the remeshing process. The results that can be obtained using the two meshing approaches for the gear pump are compared in terms of computational effort and the accuracy of the results. The two methods showed opposite results in almost all the reported results, with the overset being more precise in the radial pressure evaluation and the dynamic being more reliable in the cavitation/aeration extension cloud.

This paper wants to investigate the effects of eco-friendly fluids on the thermo-fluid-dynamic performance of external gear pumps in order to provide a first response to the increasingly urgent demands of the green economy. A computational fluid dynamics (CFD) approach based on the overset mesh technique was developed for the simulation of the full 3D geometry of an industrial pump, including all the characteristic leakages between components. A sensibility analysis of the numerical model with respect to different fluid properties was performed on a commonly used mineral oil, showing the key role of the fluid compressibility on the prediction of the pump volumetric efficiency. Moreover, the influence of temperature internal variations on both fluid density and viscosity were included. The BIOHYDRAN TMP 46 eco-friendly industrial oil and olive oil were further considered in this work, and the results of the simulations were compared for the three fluid configurations. A slightly lower volumetric efficiency was derived for the olive oil application against the other two conditions, but suggestive improvements were produced in terms of pressure and temperature distributions. Therefore, based on the obtained results, this paper encourages research activity towards the use of eco-friendly fluids in the hydraulic field.

This paper proposes a CFD methodology for the simulation of the slipper’s dynamics of a swash-plate axial piston unit under actual operating conditions. The study considers a typical slipper design, including a vented groove at the swash-plate interface. The dynamic fluid–body interaction (DFBI) model is exploited to find the instantaneous position of the slipper, while the morphing approach is adopted to cope with the corresponding mesh distortion. A modular approach is adopted to ensure high-quality mesh on the entire slipper surface and sliding interfaces provide the fluid dynamic connection between neighboring regions. The external forces acting on the slipper are included by means of user-defined lookup tables with the simulation estimating the lift force induced by fluid compression. Moreover, the force produced by the metal-to-metal contact between the slipper and the swash plate is modeled through a specific tool of the software. The pressure signal over an entire revolution of the pump is taken as an input of the simulation and a variable time step is used to manage the high-pressure gradients occurring in the regions of inner and outer dead points of the piston. The weakly compressible characteristic of the fluid is considered by a specific pressure-dependent density approach, and the two-equation eddy-viscosity k-ω SST (shear stress transport) model is used to assess the turbulent behavior of the flow. Furthermore, the transitional model predicts the onset of transition, thus solving different equations depending on whether the flow enters a laminar or turbulent regime. In conclusion, the proposed methodology investigates the motion of the slipper in response to several external forces acting on the component. The numerical results are discussed in terms of variable clearance height, pressure distribution within the gap, and lift forces acting on the slipper under specific pump operations.

The paper proposes a CFD approach for the simulation of a swash-plate axial piston pump including the full 3D geometry of the real component. Different meshing techniques are integrated in order to reproduce all the internal motions of the pump. The overset mesh procedure is used to simulate the dynamic evolution in regions’ shape and the variable orientation between parts in the piston-slipper ball joints while the alternating motion of the piston is accounted for by sliding interfaces with the neighboring regions. The multiple dynamics of the different moving elements are implemented in terms of superposing motions in order to reproduce the real position time histories as a function of the rotational speed and the swash plate inclination angle. The proposed numerical model includes all the leakages that characterize the coupling of the many components of the pump and nominal values are assumed (i.e. 10μm) throughout the entire simulation. A pressure-dependent fluid density approach is adopted to improve the performance prediction of the pump under real operating conditions. Moreover, the turbulent behavior of the flow is addressed by means of the two equation k-omega SST model. Therefore the proposed modeling approach highlights the capabilities to address any type of swash-plate axial piston pump in order to simulate the entire machine under dynamic operations; the numerical results are discussed in terms of flow ripple, pressure distribution and fluid-dynamic forces.

The paper proposes a novel concept for axels dry braking system in off-road vehicles by implementing an oil recovery system in the friction plates chamber. The new system is able to remove the oil in the discs’ chamber when they are not engaged and to replenish it when the braking system is activated and the heat generated has to be dissipated. Thus, the energy losses due to the oil splashing will be significantly reduced with remarkable effects on the fuel consumption of the vehicle. Since experimental measurements are very difficult to carry out on a real system, a simplified geometry is designed and an ad-hoc test rig realized. Fast imaging techniques are used to capture the multiphase flow pattern within the friction plates chamber at different rotational speeds of the axel. The experimental results are used to validate a full 3D multi-phase CFD approach. A good agreement between the measurements and the calculations is found. The numerical modeling is therefore employed to predict the flow distribution in the real geometry and under actual operating conditions. A modular approach is adopted for the domain subdivision in order to represent accurately the three dimensional geometrical features, while the volume of fluid approach is used to model the multi-phase flow that characterizes the component. A conjugate heat transfer model is also adopted to predict the heat transferred from the discs to the working fluid and how the fluid is dissipating the heat within the component. By means of the numerical analysis the geometry of the real system is designed in order to improve the performance of the dry braking systems both in terms of energy saving and oil cooling.

The lubrication process is a critical issue in preventing the degradation of the friction material, enhancing the efficiency of the brake system and reduce the wear behavior. The paper proposes a novel concept for axels dry braking system in off-road vehicles by implementing an oil recovery system in the friction plates chamber. The new system is able to remove the oil in the