Stefa Roos

Dr. Stefa Roos

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 November 2019 in Journal of Materials Engineering and Performance
Verified
Journal Article
Open access
PDF file
SRStefa Roos
Stefa Roos
CBCarlos Botero
Carlos Botero
JDJonas Danvind
Jonas Danvind
AKAndrei Koptioug
Andrei Koptioug
LRLars-Erik Rännar
Lars-Erik Rännar
This work focuses on the possibility of processing stainless steel 316LN powder into lightweight structures using electron beam melting and investigates mechanical and microstructural properties in the material of processed components. Lattice structures conforming to ISO13314:2011 were manufactured using varying process parameters. Microstructure was examined using a scanning electron microscope. Compression testing was used to understand the effect of process parameters on the lattice mechanical properties, and nanoindentation was used to determine the material hardness. Lattices manufactured from 316L using EBM show smooth compression characteristics without collapsing layers and shear planes. The material has uniform hardness in strut shear planes, a microstructure resembling that of solid 316LN material but with significantly finer grain size, although slightly coarser sub-grain size. Grains appear to be growing along the lattice struts (e.g., along the heat transfer direction) and not in the build direction. Energy-dispersive x-ray spectroscopy analysis reveals boundary precipitates with increased levels of chromium, molybdenum and silicon. Studies clearly show that the 316LN grains in the material microstructure are elongated along the dominating heat transfer paths, which may or may not coincide with the build direction. Lattices made from a relatively ductile material, like 316LN, are much less susceptible to catastrophic collapse and show an extended range of elastic and plastic deformation. Tests indicate that EBM process for 316LN is stable allowing for both solid and lightweight (lattice) structures.

28 April 2023 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
SRStefa Roos
Stefa Roos
CBCarlos Botero
Carlos Botero
LRLars-Erik Rännar
Lars-Erik Rännar

12 January 2021 in Metals
Verified
Journal Article
Open access
PDF file
SRStefa Roos
Stefa Roos
LRLars-Erik Rännar
Lars-Erik Rännar
Electron beam melting (EBM) is currently hampered by the low number of materials available for processing. This work presents an experimental study of process parameter development related to EBM processing of stainless steel alloy 316LN. Area energy (AE) input and beam deflection rate were varied to produce a wide array of samples in order to determine which combination of process parameters produced dense (>99%) material. Both microstructure and tensile properties were studied. The aim was to determine a process window which results in dense material. The range of AE which produced dense materials was found to be wider for 316LN than for many other reported materials, especially at lower beam deflection rates. Tensile and microstructural analysis showed that increasing the beam deflection rate, and consequently lowering the AE, resulted in material with a smaller grain size, lower ductility, lower yield strength, and a narrower window for producing material that is neither porous nor swelling.

27 August 2024 in Progress in Additive Manufacturing
Verified
Journal Article
Open access
PDF file
SRStefa Roos
Stefa Roos
LRLars-Erik Rännar
Lars-Erik Rännar
The use of additive manufacturing in metals by powder bed fusion via electron beam (PBF-EB) is increasing for fabricating high-quality parts meeting industrial standards. However, high surface roughness poses a consistent challenge in PBF-EB. This study investigates two novel approaches to optimise surface roughness for a given machine and powder combination. Using machine control software’s recently introduced research mode functionality, we develop customised beam control code to effectively explore a vast parameter space. Additionally, we explored the impact of beam travel direction and spot morphology on surface roughness. Line-melt-based contours were explored by specimen manufacturing with layer-wise parameter change, whilst spot-melting-based samples were built using a full factorial design of experiments with four factors at three levels. Initial sample characterisation was done using a stylus-based contact profilometer, followed by detailed evaluation using focus variation microscopy. Results reveal that increasing beam power and spot energy exacerbate surface roughness. We also find that a well-defined energy distribution at the spot's edge contributes to smoother surfaces. Whilst the influence of beam travel direction on surface roughness remains uncertain, our findings underscore the importance of parameter selection in achieving optimal results. By adjusting contouring parameters, we achieve a vertical roughness of Ra17.7 ± 0.9 (Sa 21.6), significantly lower than in the current literature. These findings advance our understanding of surface roughness optimisation in PBF-EB and offer practical insights for improving part quality in industrial applications. By harnessing tailored beam control strategies, manufacturers can enhance the capabilities of additive manufacturing technologies in producing metal components.

10 November 2023 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
SRStefa Roos
Stefa Roos
FFFrancesc Barbera Flichi
Francesc Barbera Flichi
LMLaia Ortiz Membrado
Laia Ortiz Membrado
CVCarlos Alberto Botero Vega
Carlos Alberto Botero Vega
EJEmilio Jiménez-Piqué
Emilio Jiménez-Piqué
LRLars-Erik Rännar
Lars-Erik Rännar

26 August 2025 in Progress in Additive Manufacturing
Verified
Journal Article
Open access
PDF file
WSWilliam Sjöström
William Sjöström
SRStefa Roos
Stefa Roos
LZLei Zhu
Lei Zhu
CBCarlos Botero
Carlos Botero
Emilio Jiménez PiqueEmilio Jiménez Pique
Emilio Jiménez Pique
LRLars-Erik Rännar
Lars-Erik Rännar
This study introduces an innovative approach for optimizing process development in electron beam powder bed fusion (PBF-EB) of non-flowing chemically reduced tungsten powder. Both line- and spot melting strategies were employed, with gradient-based variations of key processing parameters—beam current and scanning speed (line melting)/dwell time (spot melting)—applied across the XZ and XY planes on prismatic specimens. This method allowed mapping the transition from porous to swelling material within a single specimen and exposed the effects of changing gradient directions. Scripts were developed to analyze swelling and porosity from stacked backscattered electron data, providing valuable insights into material density and defect distribution. Optimal parameters for line melting (1400 W, 115 mm/s) and spot melting (1400 W, 4.5 ms dwell time) were identified, resulting in high-density samples. Solid samples were achieved with Archimedes densities of 99.8% and 99.9% respectively. Microscopical analysis verified parameter windows with dense, swelling-free material, selected for further builds and detailed characterization. Microstructural and compositional analysis was conducted using SEM and EBSD, while local micromechanical properties were assessed through micro hardness. Scaling up line melting was deemed infeasible due to warping, while spot melting was scaled to a melting area of 50 mm × 50 mm.