Lars-Erik Rännar

Lars-Erik Rännar


Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 October 2015 in Journal of Mechanical Design
Verified
Journal Article
Closed access
PDF file
MCMarie Cronskär
Marie Cronskär
LRLars-Erik Rännar
Lars-Erik Rännar
MBMikael Bäckström
Mikael Bäckström
KNKjell G Nilsson
Kjell G Nilsson
BSBörje Samuelsson
Börje Samuelsson

12 January 2021 in Metals
Verified
Journal Article
Open access
PDF file
SRStefa Roos
Stefa Roos
LRLars-Erik Rännar
Lars-Erik Rännar
Electron beam melting (EBM) is currently hampered by the low number of materials available for processing. This work presents an experimental study of process parameter development related to EBM processing of stainless steel alloy 316LN. Area energy (AE) input and beam deflection rate were varied to produce a wide array of samples in order to determine which combination of process parameters produced dense (>99%) material. Both microstructure and tensile properties were studied. The aim was to determine a process window which results in dense material. The range of AE which produced dense materials was found to be wider for 316LN than for many other reported materials, especially at lower beam deflection rates. Tensile and microstructural analysis showed that increasing the beam deflection rate, and consequently lowering the AE, resulted in material with a smaller grain size, lower ductility, lower yield strength, and a narrower window for producing material that is neither porous nor swelling.

31 May 2021 in Materials
Verified
Journal Article
Open access
PDF file
CBCarlos Botero
Carlos Botero
Aydın ŞelteAydın Şelte
Aydın Şelte
MRMarkus Ramsperger
Markus Ramsperger
GMGiulio Maistro
Giulio Maistro
AKAndrey Koptyug
Andrey Koptyug
LRLars-Erik Rännar
Lars-Erik Rännar
In this work, a highly alloyed cold work tool steel, Uddeholm Vanadis 4 Extra, was manufactured via the electron beam melting (EBM) technique. The corresponding material microstructure and carbide precipitation behavior as well as the microstructural changes after heat treatment were characterized, and key mechanical properties were investigated. In the as-built condition, the microstructure consists of a discontinuous network of very fine primary Mo- and V-rich carbides dispersed in an auto-tempered martensite matrix together with ≈15% of retained austenite. Adjusted heat treatment procedures allowed optimizing the microstructure by the elimination of Mo-rich carbides and the precipitation of fine and different sized V-rich carbides, along with a decrease in the retained austenite content below 2%. Hardness response, compressive strength, and abrasive wear properties of the EBM-manufactured material are similar or superior to its as-HIP forged counterparts manufactured using traditional powder metallurgy route. In the material as built by EBM, an impact toughness of 16–17 J was achieved. Hot isostatic pressing (HIP) was applied in order to further increase ductility and to investigate its impact upon the microstructure and properties of the material. After HIPing with optimized protocols, the ductility increased over 20 J.

26 August 2025 in Progress in Additive Manufacturing
Verified
Journal Article
Open access
PDF file
WSWilliam Sjöström
William Sjöström
SRStefa Roos
Stefa Roos
LZLei Zhu
Lei Zhu
CBCarlos Botero
Carlos Botero
Emilio Jiménez PiqueEmilio Jiménez Pique
Emilio Jiménez Pique
LRLars-Erik Rännar
Lars-Erik Rännar
This study introduces an innovative approach for optimizing process development in electron beam powder bed fusion (PBF-EB) of non-flowing chemically reduced tungsten powder. Both line- and spot melting strategies were employed, with gradient-based variations of key processing parameters—beam current and scanning speed (line melting)/dwell time (spot melting)—applied across the XZ and XY planes on prismatic specimens. This method allowed mapping the transition from porous to swelling material within a single specimen and exposed the effects of changing gradient directions. Scripts were developed to analyze swelling and porosity from stacked backscattered electron data, providing valuable insights into material density and defect distribution. Optimal parameters for line melting (1400 W, 115 mm/s) and spot melting (1400 W, 4.5 ms dwell time) were identified, resulting in high-density samples. Solid samples were achieved with Archimedes densities of 99.8% and 99.9% respectively. Microscopical analysis verified parameter windows with dense, swelling-free material, selected for further builds and detailed characterization. Microstructural and compositional analysis was conducted using SEM and EBSD, while local micromechanical properties were assessed through micro hardness. Scaling up line melting was deemed infeasible due to warping, while spot melting was scaled to a melting area of 50 mm × 50 mm.

Verified
Journal Article
Open access
PDF file
WSWilliam Sjöström
William Sjöström
LRLars-Erik Rännar
Lars-Erik Rännar
CBCarlos Botero
Carlos Botero
LMLaia Ortiz Membrado
Laia Ortiz Membrado
The use of an electron beam (EB) as a heating source in EB-based powder bed fusion (PBF-EB) has several limitations, such as reduced powder recyclability, short machine service intervals, difficulties with heating large areas and the limited processability of charge-sensitive powders. Near-infrared (NIR) heating was recently introduced as a feasible replacement and/or complement to EB heating in PBF-EB. This work further investigates the feasibility of using NIR to eliminate the need for a build platform as well as to enable easier repairing of parts in PBF-EB. NIR-assisted Ti-6Al-4V builds were successfully carried out by starting from a loose powder bed without using a build platform. The results do not only confirm that it is possible to eliminate the build platform by the aid of NIR, but also that it can be beneficial for the process cleanliness and improve the surface quality of built parts. Furthermore, a 430 stainless-steel (SS) component could be repaired by positioning it in a loose 316L SS powder bed using a fully NIR-heated PBF-EB process.

Verified
Journal Article
Open access
PDF file
CBCarlos Botero
Carlos Botero
WSWilliam Sjöström
William Sjöström
Emilio Jiménez PiqueEmilio Jiménez Pique
Emilio Jiménez Pique
AKAndrey Koptyug
Andrey Koptyug
LRLars-Erik Rännar
Lars-Erik Rännar
The ability to control process parameters over time and build space in electron beam powder bed fusion (PBF-EB) opens up unprecedented opportunities to tailor the process and use materials of a different nature in the same build. The present investigation explored the various methods used to adapt the PBF-EB process for the production of functionally graded materials (FGMs). In this way, two pre-alloyed powders—a stainless steel (SS) powder and a highly alloyed cold work tool steel (TS) powder—were combined during processing in an S20 Arcam machine. Feasibility experiments were first carried out in a downscaled build setup, in which a single powder container was installed on top of the rake system. In the container, one powder was placed on top of the other (SS/TS) so that the gradient materials were produced as the powders were spread and intermixed during the build. The process was later scaled up to an industrial machine setup, where a similar approach was implemented using two configurations of powder disposal: SS/SS + TS/TS and TS/TS + SS/SS. Each configuration had an intermediate layer of powder blend. The FGMs obtained were characterized in terms of their microstructure and local and macromechanical properties. For the microstructural analysis, optical microscopy, scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDX) were performed on the polished cross-sections. This provided evidence of gradual microstructural and compositional transitions in the samples, with a shift from SS to TS and vice versa. Nanoindentation experiments confirmed that there was a consequent gradient in the hardness, stiffness, and wear ratio from the softer and ductile SS to the harder and stiff TS. Scratch experiments revealed gradual evolution in the sliding wear behavior of the printed materials. A “progressive spring” and a “hardness-tailored punching tool” were fabricated as demonstrators. The results obtained demonstrate the great potential to gradually tailor the composition, microstructure, mechanical properties, and wear resistance by combining different powders, and they suggest that any PBF-EB system can be repurposed to build gradient materials without hardware modification. Potential applications include the tooling industry, where hard and wear-resistant materials are needed for the surfaces of tools, with tougher and more ductile materials used in the cores of tools.