Conformal metal reflectarray antennas on the surface of a cylinder are designed for millimetre‐wave applications. All depths of metal grooves in the reflectarrays are specially manipulated for high‐gain conformal reflectarray antennas. There is a good agreement between simulated and experimental radiation performance results for two different ‘sagittas’. The proposed conformal reflectarray antennas can be a helpful choice for applications requiring high‐gain antennas on curved platforms.

In this paper, we propose an X-band photonic-based pulsed radar architecture with a high range resolution. The proposed architecture is operated as a pulsed radar by adding a Mach-Zehnder modulator (MZM) operating as an optical switch to a transmitter of a conventional photonic-based frequency-modulated continuous wave (FMCW) radar. In addition, a balanced photodetector (BPD) is employed to enhance the amplitude of the received signal and remove common-mode noise. A proposed photonic-based pulsed radar prototype is implemented to operate at a center frequency of 10 GHz, a bandwidth of 640 MHz, and a pulse repetition frequency (PRF) of 1 kHz considering the performances of an arbitrary waveform generator (AWG). The implemented prototype is verified through an indoor experiment. As a result, the positions of targets are detected in real-time with 1.6% error rates of a range accuracy and obtained the range resolution of 0.26 m.

The radio frequency (RF) signal generation method using an external modulator is widely used in microwave photonics applications because it has the advantage of being able to generate coherent and stable RF signals with a higher resolution performance compared to the conventional method. A Mach–Zehnder modulator is widely used as an external modulator due to its high electro-optic coefficients and low attenuation characteristics but has a critical problem in that its electrical characteristics are changed by external environments such as temperature. In this paper, we considered the stabilization configuration to overcome this problem and propose an automatic bias control technique based on the simulated annealing algorithm of a dual-parallel Mach–Zehnder modulator (DPMZM) for quadruple signal generation. The proposed technique searches for the bias voltages of the modulator in real-time through the temperature test. In addition, the output of the quadrupled signal of the DPMZM is constantly controlled throughout the temperature range. Finally, it is confirmed that signals of a 10 GHz and 22 GHz frequency are generated using the intermediate frequency signals of a 2.5 GHz and 5.5 GHz frequency with the proposed automatic bias control technique, respectively.

Digitized beam-forming metal reflectarray antennas are designed for the millimeter-wave region. The phase control of antennas has been implemented by the reconfiguration of rectangular grooves on a metal plate. The antenna has 1147 elements arranged in an aluminum metal plate. The depths of all metal grooves are manipulated for designed phase control of high-gain beam-aimed reflectors. We have demonstrated a digitized reconfigurable metal reflectarray to steer a re-radiated millimeter-wave field from the reflector in a two-dimensional scanning plane from −20${}^{\circ }$ to 20${}^{\circ }$. The far-field patterns show that the measured gain of the 2-bit reflectarray is only 1 dB lower than that of a non-digitized reflectarray antenna. The measured peak gain is higher than 31.7 dB, and the measurements show that the gain of the full 40${}^{\circ }$ scanned beam is 31.7 dB and well-defined scanned beams are obtained with a maximum scan gain loss of 0.2 dB. The proposed reconfigurable antennas can be a useful candidate for high-gain beam-aimed antennas for practical reflecting surfaces and a variety of wireless and satellite communication systems.

We introduce a flexible multilayered THz metamaterial designed by using the Babinet's principle with the functionality of narrow band-pass filter. The metamaterial gives us systematic way to design frequency selective surfaces working on intended frequencies and bandwidths. It shows highly enhanced transmission of 80% for the normal incident THz waves due to the strong coupling of the two layers of metamaterial complementary to each other.

Reflectarray antennas composed of rectangular grooves with a digitised phase‐shift element are designed for the millimetre‐wave region. The digitised metal antennas have been realised by quantising the phase shift of each rectangular groove. For 4 bit quantised antennas, the far‐field patterns are very similar to those of the non‐digitised case and especially show that the measured gain of the 2 bit reflectarray is only 1 dB lower than that of a non‐digitised reflectarray antenna. These results will contribute to saving manufacturing cost and time and the guidance of the phase shifter for an active metal reflectarray antenna for millimetre‐wave wireless networking or imaging systems.