In this work, we present a generic approach to optimize the design of a parametrized robot gripper including both selected gripper mechanism parameters, and parameters of the finger geometry. We suggest six gripper quality indices that indicate different aspects of the performance of a gripper given a CAD model of an object and a task description. These quality indices are then used to learn task-specific finger designs based on dynamic simulation. We demonstrate our gripper optimization on a parallel finger type gripper described by twelve parameters. We furthermore present a parametrization of the grasping task and context, which is essential as an input to the computation of gripper performance. We exemplify important aspects of the indices by looking at their performance on subsets of the parameter space by discussing the decoupling of parameters and show optimization results for two use cases for different task contexts. We provide a qualitative evaluation of the obtained results based on existing design guidelines and our engineering experience. In addition, we show that with our method we achieve superior alignment properties compared to a naive approach with a cutout based on the “inverse of an object”. Furthermore, we provide an experimental evaluation of our proposed method by verifying the simulated grasp outcomes through a real-world experiment.

Autonomous take-off and landing on a moving landing pad are extraordinarily complex and challenging functionalities of modern UAVs, especially if they must be performed in windy environments. The article presents research focused on achieving such functionalities for two kinds of UAVs, i.e., a tethered multicopter and VTOL. Both vehicles are supported by a landing pad navigation station, which communicates with their ROS-based onboard computer. The computer integrates navigational data from the UAV and the landing pad navigational station through the utilization of an extended Kalman filter, which is a typical approach in such applications. The novelty of the presented system is extending navigational data with data from the ultra wide band (UWB) system, and this makes it possible to achieve a landing accuracy of about 1 m. In the research, landing tests were carried out in real conditions on a lake for both UAVs. In the tests, a special mobile landing pad was built and based on a barge. The results show that the expected accuracy of 1 m is indeed achieved, and both UAVs are ready to be tested in real conditions on a ferry.

Vibration monitoring provides a good-quality source of information about the health condition of machines, and it is often based on the use of accelerometers. This article focuses on the use of accelerometer sensors in fabricating a low-cost system for monitoring vibrations in agricultural machines, such as rotary tedders. The aim of the study is to provide useful data on equipment health for improving the durability of such machinery. The electronic prototype, based on the low-cost AVR microcontroller ATmega128 with 10-bit ADC performing a 12-bit measurement, is able to acquire data from an accelerometer weighing up to 10 g. Three sensors were exposed to low accelerations with the use of an exciter, and their static characteristics were presented. Standard experimental tests were used to evaluate the constructed machine monitoring system. The self-contained prototype system was calibrated in a laboratory test rig, and sinusoidal and multisinusoidal excitations were used. Measurements in time and frequency domains were carried out. The amplitude characteristic of the preformed system differed by no more than 15% within a frequency range of 10 Hz–10 kHz, compared to the AVM4000 commercial product. Finally, the system was experimentally tested to measure acceleration at three characteristic points in a rotational tedder, i.e., the solid grease gearbox, the drive shaft bearing and the main frame. The RMS amplitude values of the shaft vibrations on the bearing in relation to the change in the drive shaft speed of two tedders of the same type were evaluated and compared. Additionally, the parameters of kurtosis and crest factor were compared to ascertain the bearing condition.

In this work, we present a generic approach to optimize the design of a parametrized robot gripper including both gripper parameters and parameters of the finger geometry. We demonstrate our gripper optimization on a parallel jaw type gripper which we have parametrized in a 11 dimensional space. We furthermore present a parametrization of the grasping task and context, which is essential as input to the computation of gripper performance. We exemplify the feasibility of our approach by computing several optimized grippers on a real world industrial object in three different scenarios.

The paper presents an approach to design rapid and fluid movements of an universal robot to perform robot writing mimicking both the human kinematics when signing and the trajectory. To perform the task, on-line human signing standards are created first. Robot writing task is performed using these standards after that and robot signatures are acquired as a result. Next, both human and robot signatures are analyzed and compared, and the degree of signatures correlation is defined. Finally, recommendations of robot motion improvement are given.