The aims of this paper are to develop hybrid energy systems considering biomass energy sources as well as a framework and optimal configuration of hybrid systems of energy for a southern sub-urban area of Bhola district in Bangladesh, named Kukri Mukri island, and analyse the feasibility of the techno-economic prospects of these systems. In this work, electrification for the rural area is analysed for different configurations of the hybrid systems. The estimation of available resources with optimal sizing and analysis of techno-economic aspects is done through HOMER Pro software to satisfy the demand of peak load. Different configurations of hybrid energy systems, including PV/diesel, PV/wind, PV/diesel/wind, PV/wind/diesel/biomass, and wind/diesel, are analysed and compared through optimization of different energy sources in HOMER. The size of the system and components are optimized and designed depending on the net present cost (NPC) and the levelized cost of energy (LCOE). Due to the lower availability and rising cost of wind energy, the outcome of this work shows a solar-based photovoltaic (PV) as the main energy source, battery as the storage media, and diesel generator as an energy source for backup. The results indicate that LCOE is much lower for PV/wind/diesel/biomass (0.142 USD/kWh) than PV/diesel (0.199 USD/kWh), PV/wind (0.239 USD/kWh), PV/diesel/wind (0.167 USD/kWh), PV/diesel (0.343 USD/kWh), and wind/diesel (0.175 USD/kWh). Additionally, it is demonstrated from the research that the genetic algorithm (GA) process gives sustainable and cost-effective outcomes compared to HOMER.

Stiffness and forces are two fundamental quantities essential to living cells and tissues. However, it has been a challenge to quantify both 3D traction forces and stiffness (or modulus) using the same probe in vivo. Here, we describe an approach that overcomes this challenge by creating a magnetic microrobot probe with controllable functionality. Biocompatible ferromagnetic cobalt-platinum microcrosses were fabricated, and each microcross (about 30 micrometers) was trapped inside an arginine–glycine–aspartic acid–conjugated stiff poly(ethylene glycol) (PEG) round microgel (about 50 micrometers) using a microfluidic device. The stiff magnetic microrobot was seeded inside a cell colony and acted as a stiffness probe by rigidly rotating in response to an oscillatory magnetic field. Then, brief episodes of ultraviolet light exposure were applied to dynamically photodegrade and soften the fluorescent nanoparticle–embedded PEG microgel, whose deformation and 3D traction forces were quantified. Using the microrobot probe, we show that malignant tumor–repopulating cell colonies altered their modulus but not traction forces in response to different 3D substrate elasticities. Stiffness and 3D traction forces were measured, and both normal and shear traction force oscillations were observed in zebrafish embryos from blastula to gastrula. Mouse embryos generated larger tensile and compressive traction force oscillations than shear traction force oscillations during blastocyst. The microrobot probe with controllable functionality via magnetic fields could potentially be useful for studying the mechanoregulation of cells, tissues, and embryos.

Synthetic gas generated from the gasification of biomass feedstocks is one of the clean and sustainable energy sources. In this work, a fixed-bed downdraft gasifier was used to perform the gasification on a lab-scale of rice husk, sawdust, and coconut shell. The aim of this work is to find and compare the synthetic gas generation characteristics and prospects of sawdust and coconut shell with rice husk. A temperature range of 650–900 °C was used to conduct gasification of these three biomass feedstocks. The feed rate of rice husk, sawdust, and coconut shell was 3–5 kg/h, while the airflow rate was 2–3 m³/h. Experimental results show that the highest generated quantity of methane (vol.%) in synthetic gas was achieved by using coconut shell than sawdust and rice husk. It also shows that hydrogen production was higher in the gasification of coconut shell than sawdust and rice husk. In addition, emission generations in coconut shell gasification are lower than rice husk although emissions of rice husk gasification are even lower than fossil fuel. Rice husk, sawdust, and coconut shell are cost-effective biomass sources in Bangladesh. Therefore, the outcomes of this paper can be used to provide clean and economic energy sources for the near future.