yan li

Dr. yan li

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 July 2022 in Polymers
Verified
Journal Article
Open access
PDF file
YLyan li
yan li
LQLeijie Qi
Leijie Qi
YLYifan Liu
Yifan Liu
JQJunjie Qiao
Junjie Qiao
MWMaotao Wang
Maotao Wang
SLShasha Li
Shasha Li
With the continuous advancements of urbanization, the demand for power cables is increasing to replace overhead lines for energy transmission and distribution. Due to undesirable scenarios, e.g., the short circuit or poor contact, the cables can cause fire. The cable sheath has a significant effect on fire expansion. Thus, it is of great significance to carry out research on flame-retardant modification for cable sheath material to prevent fire accidents. With the continuous environmental concern, polyolefin (PO) is expected to gradually replace polyvinyl chloride (PVC) for cable sheath material. Moreover, the halogen-free flame retardants (FRs), which are the focus of this paper, will replace the ones with halogen gradually. The halogen-free FRs used in PO cable sheath material can be divided into inorganic flame retardant, organic flame retardant, and intumescent flame retardant (IFR). However, most FRs will cause severe damage to the mechanical properties of the PO cable sheath material, mainly reflected in the elongation at break and tensile strength. Therefore, the cooperative modification of PO materials for flame retardancy and mechanical properties has become a research hotspot. For this review, about 240 works from the literature related to FRs used in PO materials were investigated. It is shown that the simultaneous improvement for flame retardancy and mechanical properties mainly focuses on surface treatment technology, nanotechnology, and the cooperative effect of multiple FRs. The principle is mainly to improve the compatibility of FRs with PO polymers and/or increase the efficiency of FRs.

17 November 2021 in Energies
Verified
Journal Article
Open access
PDF file
XZXiaohua Zhang
Xiaohua Zhang
BPBo Pang
Bo Pang
YLYaxin Liu
Yaxin Liu
SLShaoyu Liu
Shaoyu Liu
KLkun liu
kun liu
QXQing Xie
Qing Xie
Partial discharge (PD) detection and analysis plays a crucial role for acceptance testing and condition monitoring of power cables. Various aspects are related to PD in power cables from theory to practice. This paper first summarizes the PD mechanism and models used for PD analysis in power cables. Afterwards, PD detection is addressed in the aspects of off-line test, on-line test, and sensors. PD analysis is discussed in detail. Specifically, related quantities and algorithms for PD analysis are outlined. PD characteristics with affecting factors, e.g., dielectric type, load, and applied voltage are discussed. Experience on PD development trend with measurements in field is analyzed. Based on the comprehensive review, challenges of PD detection and analysis along a power cable are proposed.

21 May 2024 in Polymer Testing
Verified
Journal Article
Open access
YLyan li
yan li
HSHaoyuan Song
Haoyuan Song
LQLeijie Qi
Leijie Qi
GZGuancheng Zhen
Guancheng Zhen
YLYuwei Liang
Yuwei Liang
QXQing Xie
Qing Xie

8 May 2023 in High Voltage
Verified
Journal Article
Open access
JSJingang Su
Jingang Su
LWLiqiang Wei
Liqiang Wei
PZPeng Zhang
Peng Zhang
YLyan li
yan li
YLYunpeng Liu
Yunpeng Liu
Power cable defect detection and location is a crucial aspect in power asset maintenance. Impedance spectrum measurement can be used as a non‐destructive tool for cable monitoring. Defects from overheating and moisture ingress are investigated by the authors, and it is shown that multi‐type cable defects can be detected and located by this methodology. With both electromagnetic analysis and experimental investigation, the relation between impedance variation and the dielectric permittivity is studied to reveal the method's mechanism. An approach to implement such impedance measurement online is proposed and its perspectives in terms of sensitivity is investigated by field scale tests. It is shown that 2% impedance variation due to defect should be detectable. Field scale tests show perspectives for online application with signal coupling through a high‐frequency current transformer with focus on the differences in waveforms obtained from the impedance measurements.

6 October 2022 in Energies
Verified
Journal Article
Open access
PDF file
YLyan li
yan li
YLYifan Liu
Yifan Liu
SLShasha Li
Shasha Li
LQLeijie Qi
Leijie Qi
Jun XieJun Xie
Jun Xie
QXQing Xie
Qing Xie
Dry iron core reactors are widely used in various power quality applications. Manufacturers want to optimize the cost and loss simultaneously, which is normally achieved by the designers’ experience. This approach is highly subjective and can lead to a non-ideal product. Thus, an objective dry iron core reactor design approach to balance the cost and loss with a scientific basis is desired. In this paper, a multi-objective optimal design method is proposed to optimize both the cost and loss of the reactor, which provides an automatic and scientific design method. Specifically, a three-dimensional finite element model of dry iron core reactor is established, based on which the dependency of cost and loss upon the wire size of the reactor’s winding is studied by using joint Matlab-finite element method (FEM) simulation. The Non-dominated Sorting Genetic Algorithm II (NSGA-II) is used to search for the Pareto optimal solution set, out of which the optimal wire size of the reactor is determined by using the fusion of the technique for order preference by similarity to ideal solution (TOPSIS) method and the entropy weight method. TOPSIS helps the designer to balance the concern between cost and loss, while the entropy weight method can determine the weight information through the dispersion degree of cost and loss. This methodology can avoid personal random subjective opinion when selecting the design solution out of the Pareto set. The calculation shows that the cost and loss can be reduced by up to 17.85% and 19.45%, respectively, with the proposed method. Furthermore, the obtained optimal design is approved by experimental tests.

20 August 2022 in Electric Power Systems Research
Verified
Journal Article
Open access
PWP.A.A.F. Wouters
P.A.A.F. Wouters
ADArmand van Deursen
Armand van Deursen
YLyan li
yan li