Reducing the footprint of greenhouse gases and nitrogen oxides (NOx) emissions from combustion systems means that they have been operating under lean or ultra-lean fuel–air premixed conditions. Under such conditions, self-excited large-amplitude pulsating thermoacoustic instabilities may occur, characterized by deafening combustion noises and even “violent” structural vibrations, which is, therefore, highly undesirable in practice. By conducting chemical reaction-thermodynamics-acoustics-swirling flow coupling investigations, we have numerically explored the generation and mitigation mechanisms of self-excited pulsating oscillations in a methane-fueled swirling combustor in the presence and absence of an outlet nozzle. Hence, a large-eddy simulation was performed on a fully three-dimensional compressible flow via an open-source platform, OpenFOAM. Furthermore, a thorough assessment was made to understand the fundamental physics of the interaction of the swirling flame, either constructively or destructively, to the acoustic pressure perturbations by examining the local Rayleigh criterion/index. A further explanation was made on implementing the outlet nozzle that can mitigate such periodic pulsating combustion via attenuating the fuel fraction fluctuations, vortices processing, and changing temperature field. It was also found that the dominant pulsating mode is switched from the 1/4 standing-wave wavelength mode to the 3/4 wavelength mode. Finally, more physical insights were obtained by conducting a proper orthogonal decomposition analysis on the energy distribution between the thermoacoustic modes.
In the present work, 3D Unsteady Reynolds-Averaged Navier-Stokes (URANS) simulations are performed to investigate the generation and mitigation mechanism of combustion-sustained thermoacoustic instabilities in a modelled swirl combustor. The effects of (1) swirling number SN, (2) inlet air flow rate Va and (3) inlet temperature Ti on the amplitudes and frequencies of swirling combustion-excited limit cycle oscillations are examined. It is found that the amplitude of acoustic fluctuations is increased with increasing SN and Va and decreased with the increase of Ti. The dominant frequency of oscillations is also found to increases with the increase of SN and Va. However, increasing Ti leads to the dominant frequency being decreased first and then increased. An alternative passive control method of installing an adjustable temperature heat exchanger on the combustion chamber wall is then proposed. Numerical results show that thermoacoustic oscillations could be excited and mitigated by setting the heat exchanger temperature to TH. Global and local Rayleigh indexes are applied to further reveal the excitation and attenuation effects on mechanisms. The present study is conducive to developing a simulation platform for thermoacoustic instabilities in swirling combustors. It also provides an alternative method to amplify or mitigate thermoacoustic oscillations.
Intense thermoacoustic oscillations may lead to severe deterioration due to the induced intolerable damage to combustors. A better understanding of unstable behaviors is important to prevent or suppress these oscillations. Active thermoacoustic coupling in practical combustors is caused primarily by two approaches: inherent turbulent fluctuations and the flame response to acoustic waves. Turbulent fluctuations are generally characterized by random noise. This paper experimentally expands on previous analytic studies regarding the influence of colored disturbances on the thermoacoustic response near the supercritical bifurcation point. Therein, a laboratory-scale Rijke-type thermoacoustic system is established, and both supercritical and subcritical bifurcations are observed. Then, Ornstein–Uhlenbeck (OU)-type external colored noise is introduced near the supercritical bifurcation point, and the effects of the corresponding correlation time and noise intensity D are studied. The experimental results show that these variables of the colored noise significantly influence the dynamics of thermoacoustic oscillations in terms of the most probable amplitude and autocorrelation properties. A resonance-like behavior is observed as the noise intensity or the autocorrelation time of the colored noise is continuously varied, which means that the coherent resonance occurs in the thermoacoustic system. Finally, when the system is configured closer to the stability boundary, the extent of the coherence motion is intensified in the stochastic system response. Meanwhile, the signal-to-noise ratios (SNRs) of the colored-noise-induced response are found to become more distinguished, the optimal colored noise intensity decreases, and the optimal autocorrelation time increases. These findings provide valuable guidance to predict the onset of thermoacoustic instabilities.
To enhance the performance of combustors in micro thermophotovoltaic systems, this study employs numerical simulations to investigate a planar microscale combustor featuring a counter-flow flame configuration. The analysis begins with an evaluation of the effects of (1) equivalence ratio Φ and (2) inlet flow rate Vi on key thermal and combustion parameters, including the average temperature of the combustor main wall (), wall temperature non-uniformity () and radiation efficiency (). The findings indicate that increasing Φ causes these parameters to initially increase and subsequently decrease. Similarly, increasing the inlet flow rate leads to a monotonic decline in , while the and exhibit a rise-then-fall trend. A comparative study between the proposed combustor and a conventional planar combustor reveals that, under identical inlet flow rate and equivalence ratio conditions, the use of the counterflow flame configuration can increase the while reducing the . The Nusselt number analysis shows that the counter-flow flame configuration micro-combustor achieves a larger area with positive Nusselt numbers and higher average Nusselt numbers, which highlights improved heat transfer from the fluid to the solid. Furthermore, the comparison of blow-off limits shows that the combustor with counter-flow flame configuration exhibits superior flame stability and a broader flammability range. Overall, this study provides a preliminary investigation into the use of counter-flow flame configurations in microscale combustors.
5 June 2026 in Case Studies in Thermal Engineering