In this paper, Ni–Cr–Al coatings were deposited using the detonation spraying method. The aim was to investigate how technological parameters influence coating structure formation, phase composition and tribological performances. We observed that the degree to which the barrel is filled with an O₂/C₂H₂ gas mixture strongly influences the chemical composition of manufactured coatings. High degrees of barrel filling led to a decrease in aluminum content in the coating. Filling degrees of 40% and 50% produced sprayed coatings in which only Ni–Cr phases could be found. When the filling degree was reduced up to 25%, Ni–Al phases began to form in the sprayed coatings. Gradient Ni–Cr–Al coatings were produced by gradually reducing the filling degree from 50% to 25%. These coatings are characterized by Ni–Cr near the substrate level with Ni–Cr and Ni–Al phases at higher levels. The results obtained confirm that gradient Ni–Cr–Al coatings exhibit high hardness as well as good wear resistance.

The high-strength, medium-carbon alloy construction steel 40 Kh is commonly used in the manufacture of tools and machine parts. This paper experimentally investigates the effect of electrolytic plasma thermocyclic hardening on the surface hardening and microstructure modification of 40 Kh steel. The research was carried out using optical microscopy, scanning electron microscopy, X-ray diffraction analysis and micro-hardness measurements. Modified samples were obtained at different electrolyte plasma thermal cycling modes. As a result of the heat treatment, hardened layer segments of different thicknesses and structural composition formed on the surface of the steel. The parameters and mechanisms of surface hardening were determined by examining the microstructural modification and phase transformation both before and after treatment. It was revealed that the main morphological structural-phase component of the initial state of 40 Kh steel was a ferrite–pearlite structure, and after electrolytic plasma thermocyclic hardening, the hardened martensite phase was formed. It was found that in order to achieve a hardening depth of 1.6 mm and an increase in hardness to 966 HV, the optimum time for electrolytic plasma treatment of 40 Kh steel was 2 s. The technology under discussion gives an insight into the surface hardening potential for improving the service life and reliability of 40 Kh steel.

Electrolytic plasma thermocyclic surface hardening is an attractive solution for both chemical and heat treatment used to improve the properties of the steel surface by structural and phase transformation. Structural and phase transformations occurring during the process of electrolytic plasma thermocyclic hardening are performed repeatedly at varying heating–cooling temperatures, which radically improve the quality of the part and give them properties unattainable by means of one-time processing. The impact of electrolytic plasma thermocyclic hardening modes on the structure and mechanical and tribological properties of 30CrMnSiA steel is investigated. The structural and phase components were examined using optical and scanning electron microscopy, as well as X-ray phase analysis. It is established that the structure of the cross-section is characterized by the following zonality: zone 1—a near-surface hardened zone, which is composed of hardened martensite; zone 2—thermal influence; and zone 3—a matrix consisting of pearlite and ferrite. The microhardness and wear resistance of the hardened surface were evaluated by nanoindentation and “ball on disk” methods, respectively. Nanoindentation analysis demonstrated that the indentation hardening process provides a maximum increase in hardness by three times and an increase in stiffness with a decrease in the elastic modulus by 38% compared to the original steel. The results of tribological studies show that electrolytic plasma thermocyclic hardening increases the resistance of steel to friction by increasing the surface hardness and reduces the area of actual contact during friction. It is established that the microhardness of the cross-section decreases proportionally from the surface to the depth of the layer, which is associated with a decrease in the volume content of martensite.

The article deals with the effect of irradiation with Si+ ions on phase transformations in the Ti–Al system during thermal annealing. An aluminum film with a thickness of 500 nm was deposited on VT1-00 titanium samples by magnetron sputtering, followed by ion implantation. Samples before and after irradiation with Si ions were annealed in a vacuum of 10⁻⁴ Pa in the temperature range 600–1000 °C. It was established that ion implantation reduces the dissolution of Al in α-Ti with the formation of titanium silicides (TiSi₂, Ti₅Si₃) and stabilizes aluminide phases Ti₃Al rich in aluminum. As a result, a composite structure based on titanium silicide/aluminide was obtained on the surface of the sample synthesized by complex treatment: deposition, irradiation with Si+, and thermal annealing at the near-surface layers. The formation of the phase-structural state of the implanted layers is associated with the displacement of atoms of the crystal lattice, a result that is reflected in an increase in the size of the crystal lattice and a decrease in microdistortion of the lattice. The opposite effect is observed with increasing temperature. This fact is explained by the relaxation of unstable large grains with an excess of internal energies. At the annealing temperature of 900–1000 °C, a significant increase in microhardness was observed due to silicide phases.

In recent decades, great efforts have been made to significantly improve the performance characteristics of high-speed steel using various surface hardening techniques. Electron beam modification is engaging because it has an exceptionally high thermal efficiency and can significantly improve steels’ physical and mechanical properties. This work is devoted to researching the fine structure and changing the structural phase state of the surface layer of R6M5 high-speed steel after exposure to an electron beam. Electron beam treatment of steel R6M5 was carried out on a vacuum installation. The structure and phase composition of P6M5 steel samples were studied by transmission electron microscopy. Determined that after electron irradiation, the steel structure as in the initial state consists of martensite, carbides and residual austenite. After electron irradiation, an increase in the volume fraction of lamellar martensite is observed: the fraction of lamellar martensite in the initial state is 80%, and after irradiation, it is ~90% of the total fraction of α′-martensite. The action of the electron beam led to an increase in internal stresses in α′-martensite. Revealed, the value of the scalar dislocation density in R6M5 steel after exposure to an electron beam is higher than in the initial state. A cardinal difference in the state of the material after exposure to an electron beam is the presence of bending extinction contours in all M₆C carbide particles.