Miao Senchun

Dr. Miao Senchun


Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 April 2018 in Advances in Mechanical Engineering
Verified
Journal Article
Open access
MSMiao Senchun
Miao Senchun
JYJunhu Yang
Junhu Yang
FSFengxia Shi
Fengxia Shi
XWXiaohui Wang
Xiaohui Wang
GSGuangtai Shi
Guangtai Shi
Pump as turbine is a device for energy conversion. To master the characteristics of energy transformation, especially within impeller, plays important roles for further optimum design of pump as turbine. In order to analyze the energy-changing features in detail using computational fluid dynamics, the impeller is divided into six regions by the radius. Under different operating conditions, the variations of power in the different radial cross-section of the impeller, the input net energy in different regions of the impeller, and the energy from the fluid to the impeller were demonstrated. The results show that the pressure energy of fluid is primary for impeller work, instead of the kinetic energy; the front and middle regions of the impeller (about the area of (0.6–1.0) D2) are important parts for energy conversion; in the rear area of the impeller, it acquires little energy from fluid relatively, what’s more, the fluid not only does not work to impeller, but also consumes the impeller mechanical energy under the large flow conditions. So this research may point out the direction for optimization design of the impeller blade.

1 September 2015 in Advances in Mechanical Engineering
Verified
Journal Article
Open access
MSMiao Senchun
Miao Senchun
JYJun-Hu Yang
Jun-Hu Yang
GSGuang-Tai Shi
Guang-Tai Shi
TWTing-Ting Wang
Ting-Ting Wang
One major focus on the performance researches of pump as turbine is how to enhance the efficiency of energy recovery. While the key point of increasing the efficiency is to improve the performance of the blade profile which is structural basis of the blade geometry. This article presents an optimization method for the blade profile. It contained the parameterization of blade profile, the Latin Hypercube experimental design, the computational fluid dynamics techniques, the back propagation neural network, and genetic algorithm. Specifically, the nonuniform cubic B-spline curve was used to parameterize the blade profile, the Latin Hypercube experimental design method for the acquirement of the sample points of back propagation neural network. The performance analysis of each sample point was accomplished by the computational fluid dynamics techniques. Then, the learning and training of the back propagation neural network was carried out. Finally, the optimization techniques of combining the back propagation neural network and genetic algorithm were used to solve the optimization problems of the blade profile. Based on the above method, the blade profile of a pump as turbine was optimized and improved. The result shows that the efficiency of the optimized pump as turbine under the optimum operating condition was increased by 2.91%, with the constraint condition to ensure that the difference between the head and the initial head of the pump as turbine is less than the specified value. This proves that using the above method to optimize the blade profile is feasible.

1 October 2020 in Science Progress
Verified
Journal Article
Open access
PDF file
MSMiao Senchun
Miao Senchun
ZHZhang Hong-Biao
Zhang Hong-Biao
WTWang Ting-Ting
Wang Ting-Ting
WXWang Xiao-Hui
Wang Xiao-Hui
SFShi Feng-Xia
Shi Feng-Xia
In order to make the pump as turbine (PAT) run efficiently and safely, a multidisciplinary optimization design method for PAT blade, which gives consideration to both the hydraulic and intensity performances, is proposed based on multidisciplinary feasibility (MDF) optimization strategy. This method includes blade parametric design, Latin Hypercube Sampling (LHS) experimental design, CFD technology, FEA technology, GA-BP neural network and NSGA-II algorithm. Specifically, a parameterized PAT blade with cubic non-uniform B-spline curve is adopted, and the control point of blade geometry is taken as the design variable. The LHS experimental design method obtains the sample points of training GA-BP neural network in the design space of variables. The hydraulic performance of each sample point (including the hydraulic pressure load on the blade surface) and the strength performance analysis of blades are completed by CFD and FEA technology respectively. In order to save calculation time of the whole optimization design, the multi-disciplinary performance analysis of each sample in the optimization process is completed by single-coupling method. Then, GA-BP neural network is trained. Finally, the multi-disciplinary optimization design problem of PAT blade is solved by the optimization technology combining GA-BP neural network and NSGA-II algorithm. Based on this optimization method, the PAT blade is optimized and improved. The efficiency of the optimized PAT is improved by 1.71% and the maximum static stress on the blade is reduced by 7.98%, which shows that this method is feasible.

1 November 2024 in Physics of Fluids
Verified
Journal Article
Closed access
MSMiao Senchun
Miao Senchun
LLLeqi Liu
Leqi Liu
XWxiaohui wang
xiaohui wang
JYJunhu Yang
Junhu Yang
Pump as turbine (PAT) is an efficient, simple, and cost-effective equipment combining pump and turbine and is one of the excellent energy recovery devices. It is helpful to master the flow characteristics of the key component impeller for the further optimization and design of the PAT. To analyze the unsteady flow features in the impeller of a double-suction pump operating as a turbine, numerical simulations were conducted using the shear stress transport (SST) k-ω turbulence model at the designed operating conditions. By utilizing proper orthogonal decomposition (POD) and dynamic mode decomposition (DMD) methods on the unsteady velocity field of a single cycle, the dominant modes up to the fourth order, along with their respective space–time information, can be extracted. The velocity field and vorticity field analysis were performed on the first four modes extracted using two different methods. Additionally, the vortex structures were extracted using the Ω method. The analysis demonstrates that the POD and DMD methods effectively decompose the intricate flow characteristics within the impeller into dynamic–static interference modes, fundamental modes, and dissipative modes. The dynamic–static interference mode is dominant, reflecting the flow characteristics influenced by the stationary components within the impeller. The vortex structure is mainly small tubular vortex and point vortex. The fundamental mode captures the steady flow field characteristics caused by the blade channel geometry. The vortex structure is mainly continuous tubular vortex and the diameter becomes larger. The dissipative mode reflects the flow separation generated on the blades by disturbances from the stationary components. The vortex structure is dominated by point vortex and discontinuous tubular vortex. Comparing the outcomes of the two modal analysis methods shows that the POD method has a distinct advantage in showcasing key changing nodes. In contrast, the DMD method is superior in isolating modes with a single frequency and in determining their stability.

1 January 2021 in Fluid Dynamics & Materials Processing
Verified
Journal Article
Open access
MSMiao Senchun
Miao Senchun
HZHongbiao Zhang
Hongbiao Zhang
WTWanglong Tian
Wanglong Tian
YLYinqiang Li
Yinqiang Li
To study the unsteady flow and related energy conversion process in the volute of a pump-as-turbine (PAT) device, six different working conditions have been considered. Through numerical calculation, the spatio-temporal variation of static pressure, dynamic pressure, total pressure and turbulent energy dissipation have been determined in each section of the volute. It is concluded that the reduction of the total power of two adjacent sections of the PAT volute is equal to the sum of the power lost by the fluid while moving from one section to the other and the power output from the two adjacent sections. For a fixed flow rate, the percentage of static pressure energy at the outlet of the PAT is roughly similar to that of the corresponding volute section, and both show a gradually increasing trend. The turbulent dissipation rate on each section of the PAT volute displays a similar a spatio-temporal behavior for different flow rates.

1 January 2021 in Fluid Dynamics & Materials Processing
Verified
Journal Article
Open access
MSMiao Senchun
Miao Senchun
HZHongbiao Zhang
Hongbiao Zhang
FSFengxia Shi
Fengxia Shi
XWXiaohui Wang
Xiaohui Wang
XMXijin Ma
Xijin Ma
A volute is a curved funnel with cross-sectional area increasing towards the discharge port. The volute of a centrifugal pump is the casing hosting the fluid being pumped by the impeller. In Pump-as-turbine devices (PAT), vice versa the volute plays the role of energy conversion element. In the present analysis, this process is analyzed using CFD. The results show that in the contraction section of volute the conversion between dynamic pressure energy and static pressure energy essentially depends on the reduction of flow area, while in the spiral section, frictional losses also play a significant role. From the throat to the end of the volute, the flow decreases in a wave-like manner.