Robots are very essential for modern nuclear power plants to monitor equipment conditions and eliminate accidents, allowing one to reduce the radiations on personnel. As a novel robot, a soft robot with the advantages of more degrees of freedom and abilities of continuously bending and twisting has been proposed and developed for applications in nuclear power industry. Considering the radiation and high-temperature environment, the overall performance improvement of the flexible materials used in the soft nuclear robot, such as the tensile property and gamma-ray shielding property, is an important issue, which should be paid attention. Here, a flexible gamma-ray shielding material silicone-W-based composites were initially doped with nano titanium oxide and prepared, with the composition of 20 silicone-(80-x) W-(x) TiO2, where x varied from 0.1 to 2.0 wt.%. Structural investigations on SEM and EDS were performed to confirm the structure of the prepared composites and prove that all the chemicals were included in the compositions. Moreover, the tensile property of the composites at 25, 100, and 150 °C were investigated to study the effect of working temperature on the flexibility of the compositions. The attenuation characteristics including the linear attenuation coefficients and mass attenuation coefficients of the prepared silicone-W or silicone-W-TiO2-based composites with respect to gamma ray were investigated. The stability of the silicone–tungsten-TiO2-based composite at high temperature was studied for the first time. In addition, the influence of nano TiO2 additive on the property’s variation of silicone-W-based composites was initially studied. The comparison of the properties such as the tensile elongation, thermal stability, and gamma-ray shielding of the synthesized silicone-W and silicone-W-TiO2 composites showed that the addition of nano TiO2 powders could be useful to develop novel gamma-ray-shielding materials for radiation protection of soft robots or other applications for which soft gamma-ray-shielding materials are needed.
Under the load of an internal explosion shock wave, the failure of a cylindrical shell is the basis of safety evaluation and failure analysis of explosion vessel design. This paper carried out the explosion loading experiment of a cylindrical shell, and used the nonlinear dynamic finite element analysis program LS-DYNA for the dynamic response of the cylindrical shell along the directions of thickness and length, and analyzed the failure law of a cylindrical shell. The results showed that the deformation of the core section of the cylindrical shell was not different in the same specific distance, the strain decreased more slowly with the increase of thickness at the end of the explosion center, and the expansion failure process and fracture mode of metal shell under explosive load were affected by the material and structure size of the shell, as well as the characteristics and mode of the load. Based on the plastic theory, this paper discussed the evolution characteristics of the stress state during the expansion process of cylindrical shells under different explosion pressures, and analyzed the explosion pressure effect on the tensile fracture and shear fracture. The expansion failure experiment of a 20# steel-made cylindrical shell and the microscopic and metallographic analysis of the recovered debris were carried out.
X-ray thermodynamic effect is an important damage mode for spacecraft. Blow-off impulse as the main thermodynamic damage parameter has been widely studied by combining laboratory and numerical simulations. In this paper, most calculations and analyses have been carried out by using the self-developed software RAMA, including the equivalent calculation of blow-off impulse of monoenergetic and blackbody X-ray, and soft/hard blackbody X-ray irradiated at different incidence angles of LY-12 aluminium target. The results show that the characteristic mono-energetic X-ray can be exploited to simulate the blow-off impulse of the blackbody X-ray under certain conditions as a feasible equivalent method for the equal-flux and equal-impulse relations between mono-energetic and intense pulse blackbody of blow-off impulse. Moreover, the equivalent thermodynamic effect can be achieved between the point source radiation and parallel X-ray of X-ray. Furthermore, the cosine distribution of blow-off impulse is conducive to designing and calculating X-ray radiation load of hard aluminium corresponding to 1–5 keV blackbody spectrum. The mentioned results can be referenced for pulse X-ray simulation source and enhance the fidelity of the thermal-mechanical effect by electron beam. It is noteworthy that the study on the thermodynamic effects of intense pulsed X-ray is of high significance.
Carbon/Phenolic (C/P), a typical anisotropic material, is an important component of aerospace and often used to protect the thermodynamic effects of strong X-ray radiation. In this paper, we establish the anisotropic elastic-plastic constitutive model, which is embedded in the in-house code “RAMA” to simulate a two-dimensional thermal shock wave induced by X-ray. Then, we compare the numerical simulation results with the thermal shock wave stress generated by the same strong current electron beam via experiment to verify the correctness of the numerical simulation. Subsequently, we discuss and analyze the rules of thermal shock wave propagation in C/P material by further numerical simulation. The results reveal that the thermal shock wave represents different shapes and mechanisms by the radiation of 1 keV and 3 keV X-rays. The vaporization recoil phenomenon appears as a compression wave under 1 keV X-ray irradiation, and X-ray penetration is caused by thermal deformation under 3 keV X-ray irradiation. The thermal shock wave propagation exhibits two-dimensional characteristics, the energy deposition of 1 keV and 3 keV both decays exponentially, the energy deposition of 1 keV-peak soft X-ray is high, and the deposition depth is shallow, while the energy deposition of 3 keV-peak hard X-ray is low, and the deposition depth is deep. RAMA can successfully realize two-dimensional orthotropic elastoplastic constitutive relation, the corresponding program was designed and checked, and the calculation results for inspection are consistent with the theory. This study has great significance in the evaluation of anisotropic material protection under the radiation of intense X-rays.
The silver acetylene silver nitrate loading technology of the light initiated high explosive, as one of important means to simulate the structural response of powerful pulsed X-ray, adopts the pulse laser initiation. It has advantages of improvement of practical control, heterogenous loading realization and simultaneous loading timeliness. In this paper, the physical and mathematical models of hot spot initiation and photochemical initiation of energetic materials under the action of laser are firstly established, and then the laser initiation mechanism of the light initiated high explosive is specifically analyzed, and the laser initiation experiment is conducted based on the optical adsorption property of the light initiated high explosive. From this study, the laser initiation thresholds of 193 nm, 266 nm, 532 nm, 1064 nm wavelengths are given, and they are 5.07 mJ/mm2, 6.77 mJ/mm2, 7.21 mJ/mm2 and 10.61 mJ/mm2, respectively, and the complete detonation process is verified by detonation velocity. This work technically supports the study of pulse laser initiation process, mechanism and explosion loading rule as well as the loading technology of the light initiated high explosive to simulate the structural response of X ray.
The electron beam, one of the most effective approaches to simulate the irradiation effects of powerful pulsed X-ray in the laboratory, plays an important role in simulating the thermodynamic effects of powerful pulsed X-ray. This paper studies the thermodynamics equivalence between multienergy composite spectrum electron beam and blackbody spectrum X-ray, which is helpful to quickly determine the experimental parameters in the simulation experiment. The experimental data of electron beam are extrapolated by numerical calculation, to increase the range of energy flux. Through calculating the blow-off impulse of blackbody spectrum X-ray irradiation, we obtained the curve of X-ray blow-off impulse varying with energy flux, and then found two categories of equivalent relations—equal-energy flux and equal-impulse—by analyzing the calculation results of electron beam and X-ray blow-off impulse. Based on such relations, we could directly or indirectly obtain the results of blackbody spectrum X-ray irradiation blow-off impulse via electron beam experiment.