Àngela Puig-Sirera

Dr. Àngela Puig-Sirera

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 September 2021 in Water
Verified
Journal Article
Open access
PDF file
ÀPÀngela Puig-Sirera
Àngela Puig-Sirera
Giovanni RalloGiovanni Rallo
Giovanni Rallo
Paula ParedesPaula Paredes
Paula Paredes
Teresa A. PaçoTeresa A. Paço
Teresa A. Paço
Mario MinacapilliMario Minacapilli
Mario Minacapilli
Luis Santos PereiraLuis Santos Pereira
Luis Santos Pereira
The SIMDualKc model was applied to evaluate the crop water use and the crop coefficient (Kc) of an irrigated olive grove (Olea europaea L.) located in Sicily, Italy, using experimental data collected from two crop seasons. The model applies the FAO56 dual Kc approach to compute the actual crop evapotranspiration (ETc act) and its components, i.e., the actual tree transpiration (Tc act), obtained through the basal crop coefficient (Kcb), and soil evaporation according to an evaporation coefficient (Ke). Model calibration was performed by minimizing the difference between the predicted Tc act and the observed daily tree transpiration measured with sap flow instrumentation (TSF field) acquired in 2009. The validation was performed using the independent data set of sap flow measurements from 2011. The calibrated Kcb was equal to 0.30 for the initial and non-growing season stages, 0.42 for the mid-season, and 0.37 for the end season. For both seasons, the goodness-of-fit indicators relative to comparing TSF field with the simulated Tc act resulted in root mean square errors (RMSE) lower than 0.27 mm d−1 and a slope of the linear regression close to 1.0 (0.94 ≤ b0 ≤ 1.00). The olive grove water balance simulated with SIMDualKc produced a ratio between soil evaporation (Es) and ETc act that averaged 39%. The ratio between actual (ETc act) and potential crop evapotranspiration (ETc) varied from 84% to about 99% in the mid-season, indicating that the values of ETc act are close to ETc, i.e., the adopted deficit irrigation led to limited water stress. The results confirm the suitability of the SIMDualKc model to apply the FAO56 dual Kc approach to tree crops, thus assessing the water use of olives and supporting the development of appropriate irrigation management tools that are usable by farmers. A different way to estimate Kcb is based on the approach suggested in 2009 by Allen and Pereira (A&P), which involves the measured fraction of ground covered (shaded) by the crop and the height of the trees. Its application to the studied grove produced the mid-season Kcb values ranging from 0.40–0.45 and end-season Kcb values ranging from 0.35–0.40. The comparison between the A&P-computed Tc act A&P and TSF field shows RMSE values ranging from 0.27 to 0.43 mm d−1, which demonstrates the adequacy of the latter approach for parameterizing water balance models and for irrigation scheduling decision making.

30 October 2024 in Agricultural Water Management
Verified
Journal Article
Open access
FHFatma Hamouda
Fatma Hamouda
ÀPÀngela Puig-Sirera
Àngela Puig-Sirera
Lorenzo BonziLorenzo Bonzi
Lorenzo Bonzi
DRDamiano Remorini
Damiano Remorini
RMRossano Massai
Rossano Massai
Giovanni RalloGiovanni Rallo
Giovanni Rallo

27 January 2022 in Agronomy
Verified
Journal Article
Open access
PDF file
ÀPÀngela Puig-Sirera
Àngela Puig-Sirera
Marco AcutisMarco Acutis
Marco Acutis
MBMarialaura Bancheri
Marialaura Bancheri
Antonello BonfanteAntonello Bonfante
Antonello Bonfante
MBMarco Botta
Marco Botta
Angelo BasileAngelo Basile
Angelo Basile
Adoption of zero-tillage practices with residue retention in field crops has been introduced as an alternative soil-management technique to counteract the resource degradation and high production costs derived from intensive tillage. In this sense, the biophysical models are valuable tools to evaluate and design the most suitable soil-management technique in view of future climate variability. The aim of this study was to use the ARMOSA process-based crop model to perform an assessment of tillage (T) and no-tillage (No-T) practices of durum-wheat-cropping systems in the Campania region (South of Italy) under current and future climate scenarios. First, the model was calibrated using measurements of soil water content at different depths, leaf area index, and aboveground biomass in the T and No-T treatments during the 2013–2014 season. Then, the model was further applied in the T and No-T treatments to future climate data for 2020–2100 that was generated by the COSMO-CLM model using the RCP4.5 and 8.5 paths. Results of the calibration depicted that the model can accurately simulate the soil-crop-related variables of both soil-management treatments, and thus can be applied to identify the most appropriate conservation agricultural practices in the durum-wheat system. The simulation of soil water content at different depths resulted in small relative root mean square errors (RRMSE < 15%) and an acceptable Pearson’s correlation coefficient (r > 0.51); and the goodness-of-fit indicators for simulated LAI and AGB resulted in acceptable RRMSE (RRMSE < 28%), and high r (r > 0.84) in both soil-management treatments. Future climate simulations showed that No-T management will deliver 10% more wheat yield than the T, with an annual average 0.31% year−1 increase of soil organic carbon, and an increase of 3.80% year−1 for N uptake, which can diminish the N leaching. These results suggest that No-T could be implemented as a more resilient management for farming system in view of climate uncertainty and scarcity of resources. Therefore, these findings support the potential of the ARMOSA model to evaluate the soil-crop response of the durum-wheat system under different management conditions and to design appropriate soil-management practices for current and future climate predictions.

20 January 2025
Verified
Conference Paper
Open access
MCMarco Carrara
Marco Carrara
Lorenzo BonziLorenzo Bonzi
Lorenzo Bonzi
FHFatma Hamouda
Fatma Hamouda
MSMino Sportelli
Mino Sportelli
ÀPÀngela Puig-Sirera
Àngela Puig-Sirera
Giovanni RalloGiovanni Rallo
Giovanni Rallo
This study aimed to assess and compare the performance of EM38 (Geonics Limited) and Syscal-Pro (Iris instruments) EMI tools in soil spatial heterogeneity mapping. Mainly, the two tools were evaluated for their ability to explain the spatial variability of the soil resistivity, which strongly correlates with the soil’s physical status properties. Moreover, the effect of two surface soil roughness caused by two different tillage modalities has been studied.The experimental plot (30 m width x 100 m length) consisted of an agroforestry system located in San Piero a Grado (Pisa, Italy, (, 43°41’07” N, 10°20’32” E). Two 100-meters length deep open drains were located on the edges. The soil texture is loam, with clay content values from 7.64% to 15.14% and sand content ranging from 22.36% to 49.37%. The intercropping system consisted of wheat (Triticum aestivum L) and pea (Pisum Sativum L) in the inner part of the field, and two rows of poplar (Populus x euramericana Dode Guiner) on the edges experimental plot.Data were acquired before seed-bed preparation by pulling the two tools over the soil. For the Syscal-pro, 13 cylindrical stainless-steel electrodes were pulled by a tractor, allowing soil resistivity data acquisition according to the reciprocal Wenner-Schlumberger array (Telford, 1976). A total of five transects with 5 m spacing were spanned to the inner field zone, whereas four additional transects allowed to detail the resistivity gradients closed the two deep open drains.Regarding the EM38 tool, a preliminary laboratory activity allowed the development of a specific data acquisition (DAQ) system for continuous monitoring of the resistivity data recording and spatializing. This DAQ system is based on a CR1000 Data logger (Campbell Scientific, United States), which allows collecting the speed and position of the EM-38 device by carrying it on a specifically designed sled system.Two Garmin’s GPS (model 79S/SC for Syscal Pro and model GPS16X-HVS for the EM38) enabled georeferencing the collected data.Preliminary results have shown a range of electrical conductivity values between 30 mS/m and 45 mS/m, spatially distributed according to the pattern obtained by Syscal-Pro. Further investigation is required to better understand the relationship between EM38 and Syscal-Pro measurements, after which the vertical domain explored has been standardised between the two methods.Keywords: Agroforestry system, EM38, Syscal, soil bulk resistivity, soil bulk conductivity, spatial variability.

20 January 2025
Verified
Conference Paper
Open access
EDEmanuele Dichio
Emanuele Dichio
Lorenzo BonziLorenzo Bonzi
Lorenzo Bonzi
Giovanni RalloGiovanni Rallo
Giovanni Rallo
ÀPÀngela Puig-Sirera
Àngela Puig-Sirera
DRDamiano Remorini
Damiano Remorini
RMRossano Massai
Rossano Massai
Abstract The weather-based approach quantifies the crop water requirements (CWR) using a simplified agrohydrological model coupled with meteorological sensors. The FAO56 model (Allen et al., 1998) is one of the most used bucket models for CWR. In this model, the daily ET0 is usually estimated by the FAO-Penman-Monteith (PM), which needs as inputs standard atmosphere forcings acquired from weather stations, that often are equipped with ordinary mechatronics sensors that require regular maintenance. An atmometer (ETgage) is an accurate sensor with no moving parts that continuously measures the ET0 based on a physical analogy of the crop reference. This study aims to design and validate an expert system, named Irrigatmo, to manage irrigation based on the combined application of the feedforward- (FFc) and feedback- (FBc) control irrigation scheduling protocols. The FFc protocol comprises a Kc-based mass balance model with a modified atmometer and FDR sensors for sub-hourly ET0 and soil water content (SWC) measurements. At the same time, the FBc protocol uses the SWC to quantify the critical condition and the crop stress coefficient to adjust the Kcb value used in the bucket model. The system was implemented in proprietary logic (CR300, Campbell Scientific Inc.) and open-source logic (Arduino Mega 2560, Arduino). The core of the system implements a weather-based water balance model, trained by a modified atmometer and soil moisture sensor for sub-hourly scale ET0 and SWC, as well as an infrared thermometer and a contact thermocouple for quantifying the crop water stress index (CWSI). The ETgage was modified by integrating a pressure transducer sensor, calibrated to measure the water level inside the atmometer tank continuously. The results showed that Irrigatmo accurately and rapidly detected the changes in atmospheric and soil water conditions. The system can directly calculate the evapotranspiration reduction factor (Ks), estimating the CWSI based on canopy temperature measurements. This could overcome the uncertainty in the models associated with the water stress function based solely on the soil moisture. The system was built and calibrated within the AgrHySMo laboratory of DiSAAA-a and validated on a commercial kiwifruit orchard of Actinidia chinensis var. chinensis 'Zesy002'. The field testing made it possible to validate the system's ability to model the water stress functions of the crop and the sensitivity to identify the critical water status conditions that mark the transition to a limiting condition. Irrigatmo could manage irrigation autonomously, activating or turning off the solenoid valves, and returning to our field the amount of water lost during the evapotranspiration processes. Future perspectives consider the implementation of the proposed system in a wireless sensor network (WSN) and at the interfacing of the WSN nodes with aerial platforms where the edge-computing systems specialized also in the control of IoT-irrigation actuators will be located.

15 May 2023
Verified
Conference Paper
Open access
FHFatma Hamouda
Fatma Hamouda
Lorenzo BonziLorenzo Bonzi
Lorenzo Bonzi
GPGiuseppe Provenzano
Giuseppe Provenzano
ÀPÀngela Puig-Sirera
Àngela Puig-Sirera
ASAndrea Sbrana
Andrea Sbrana
Giovanni RalloGiovanni Rallo
Giovanni Rallo
The EM-38 is a Handheld Electrical Magnetic Induction (EMI) device, non-invasive and commonly used for monitoring salinity, mapping bulk soil properties, and evaluating soil nutrient status. The measured data is an electrical conductivity, [mS/m], which was referred to a representative soil volume of 1.0-1.5 m depth and 2.0 m width.The Data AcQuisition (DAQ) system for EM-38 (Geonics Inc.) conductivity meter, used for recording the spatial variability of the soil bulk electrical conductivity (EC), is expensive, according to the proprietary software, and do not provide detailed, modifiable circuit schematics.To address these issues, we developed an easy-to-use, modifiable, and inexpensive data acquisition (DAQ) system for EC data recording and spatializing. In particular, this work investigates the feasibility of using a low-cost open-source DAQ system to be installed on an EM-38 conductivity meter (Geonics Inc.). This DAQ system is based on Raspberry Pi and allows collecting speed and position of the EM-38 device by carrying it on a specific designed sled system.The EM-38 data (± 200mV) were acquired by A/D converter 24 bit and GPS data ($GPGGA, $GPRMC [NMEA 0183]) were obtained by serial input RS232. The Data logger (Raspberry Pi 4) stored the acquired data and transferred it to the server using an internet connection (Router 4G). The control Firmware has been written in Python language. To ensure the accuracy and reliability of the collected data, the system has been evaluated and tested in well-known open-filed (CIRAAA-a reserch center of the University of Pisa), where the spatial variability of the main soil physical properties (i.e. soil texture, organic matter, electrical conductivity) are known.The performance has been evaluated by comparing the data string with the one generated by a professional DAQ system. The latter includes a CR1000 data logger (Campbell Scientific) to control and store the EC data and integrats a GPS receiver (GPS16X-HVS, Garmin Inc.) which provides the position, velocity, and timing information.First results allowed to approve the possibility to extract the analogical signal from the device, which is strongly responsive to the variation of the physical properties of the soil environment. Moreover, the device is able to estimate accurately the spatial patterns of the investigated soil physical properties. Keywords: Precision farming, Zoning, EMI sensors, soil bulk electrical conductivity, open source DAQ
1