Martensitic stainless steel type AISI420 was plasma nitrided at 673 K for 3.6 ks to investigate the initial stage of the nitrogen supersaturation process without the formation of iron and chromium nitrides. SEM-EDX, electron back-scattering diffraction (EBSD), and TEM analyses were utilized to characterize the microstructure of the nitrided layer across the nitriding front end. The original coarse-grained, fully martensitic microstructure turned to be α’- γ two phase and fine-grained by high nitrogen concentration. Below this homogeneously nitrided layer, α’-grains were modified in geometry to be aligned along the plastic slip lines together with the α’ to γ-phase transformation at these highly strained zones. Most of these α’-grains in the two-phase microstructure had a nano-laminated structure with the width of 50 nm.
A tool steel type SKD11 punch was plasma carburized at 673 K for 14.4 ks at 70 Pa to make carbon supersaturation. This carburized SKD11 punch was employed for upsetting the pure titanium wire with the diameter of 1.00 mm up to the reduction of thickness by 70% in a single shot. Its contact interface to titanium work was analyzed to describe the anti-galling behavior in this forging. Little trace of titanium proved that the galling process was suppressed by the in situ solid lubrication. The isolated free carbon agglomerates are wrought as a solid lubricant to sustain the galling-free forging process. This anti-galling upsetting reduced the residual strains in the forged wires. A long titanium wire with a length of 45 mm was incrementally upset to yield the titanium ribbon with a thickness of 0.3 mm, the width of 2.3 mm, and the length of 50 mm. The grain size of original pure titanium was much reduced to 2 μm on average. A micro-pillared microtexture was imprinted onto this forged titanium ribbon.
A bare AISI420J2 punch often suffers from severe adhesion of metallic titanium as well as titanium oxide debris particles in dry, cold forging of biomedical titanium alloys. This punch was plasma-carburized at 673 K for 14.4 ks to harden it up to 1200 HV on average and to achieve carbon supersaturation in the carburized layer. This plasma-carburized punch was employed in the cold, dry forging of a pure titanium wire into a flat plate while reducing the thickness by 70%. The contact interface width approached the forged workpiece width with increasing the reduction ratio. This smaller bulging deformation reveals that the workpiece is upset by homogeneous plastic flow with a lower friction coefficient. This low-friction and anti-galling forging process was sustained by an in situ solid lubrication mechanism. Unbound free carbon was isolated from the carbon-supersaturated AISI420J2 matrix and deposited as a thin tribofilm to protect the contact interface from mass transfer of metallic titanium.
A thick β-SiC CVD (chemical vapor deposition)-coated SiC device was developed as a new punch and die system for dry, cold forging of pure titanium and austenitic stainless-steel works. This β-SiC coating thickness was 4 mm, enough to make mechanical machining of a cavity into β-SiC coating core die. These β-SiC-coated punch and core dies were fixed into the cassette die for dry, cold forging experiments. The stainless steel and titanium wires with diameters of 1.0 mm were employed as the work material. Different from the conventional metallic and ceramic die systems suffering from work material transfer, this system sustained the galling-free cold, dry forging behavior up to a higher reduction of thickness than 30%. The power to stroke the relationship was in situ monitored to describe this forging behavior up to the specified reduction of the wires together with observations on the geometric change from a circular wire to a pentagonal prism bar. Precise scanning electron microscopy-electron-dispersive X-ray spectroscopy (SEM-EDX) analyses were performed to describe the material compatibility on the contact interface between β-SiC coating and elastoplastically deforming works.
The AISI316 austenitic stainless steel die was prepared and nitrided at 673 K for 14.4 ks. Through this low temperature plasma nitriding, the AISI316 die was homogeneously hardened up to 1400 HV within its surface layer of 50 μm. This nitrided AISI316 die was utilized to print the tailored micropattern with nanotextures onto its surface by the femtosecond laser processing. Each micropattern consisted of the tailored segments to have unidirectional nanotextures with different orientations. Each segment was recognized by its intrinsic surface plasmonic brilliance to tailored nanotextures. The CNC (Computer Numerical Control) stamping system was used to coin these micropatterns with nanotextures onto the AA1060 aluminum plates with the thickness of 1 mm. SEM (Scanning Electron Microscopy) and optical microscopy were employed to characterize the original micro-/nano-textures on the AISI316 die as well as the coined nanotextured patterns on the AA1060 plate surfaces.
Fine-grained austenitic stainless steels (FGSS) were plasma nitrided below 700 K to describe their microstructure evolution during the nitrogen supersaturation process and to investigate the post-stressing effect on the microstructure and mechanical properties of nitrided FGSS. Normal- and fine-grained AISI304 plates were nitrided at 623 K and 673 K to investigate the grain size effect on the nitrogen supersaturation process as well as the microstructure evolution during the nitriding process. Fine-grained AISI316 (FGSS316) wires were nitrided at 623 K to demonstrate that their outer surfaces were uniformly nitrided to have the same two-phase, refined microstructure with high nitrogen solute content. This nitrided FGSS316 wire had a core structure where the original FGSS316 core matrix was bound by the nitrided FGSS316 layer. The nitrided wire had higher stiffness, ultimate strength, and elongation in the uniaxial tensile testing than its un-nitrided wires. The core microstructure was refined and homogenized by this applied loading together with an increase of nitrided layer hardness.