Tomomi Shiratori

Prof. Dr. Tomomi Shiratori

orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 April 2020 in Applied Sciences
Verified
Journal Article
Open access
PDF file
TATatsuhiko Aizawa
Tatsuhiko Aizawa
TSTomomi Shiratori
Tomomi Shiratori
YKYoshihiro Kira
Yoshihiro Kira
TITadahiko Inohara
Tadahiko Inohara
In this study, a CVD (Chemical Vapor Deposition)-diamond coated tungsten carbide cobalt (WC (Co)) punch was trimmed to adjust its surface roughness and to significantly reduce its edge curvature for fine piercing by femtosecond laser processing. Through this laser trimming, the surface quality of the diamond coating and the punch edge profile were improved to less than 0.5 μm at the maximum roughness and 2 μm in the edge width, respectively. In parallel with this improvement of surface quality, the side surface of the diamond coating was modified to include nano-textures via the LIPSS (Laser Induced Periodic Surface Structuring) process. Through the fine piercing process, this nanotexture was transcribed onto the pierced hole surface together with fine shearing of the hole by piercing. WLI (White-Light Interferometry) and SEM (Scanning Electron Microscopy) were utilized to describe this transcription of nanotextures during the piercing process. These semiregular nanotextures with an LIPSS period of 300 nm on the pierced hole surface induced a blue colored surface plasmon.

23 June 2022 in Applied Mechanics
Verified
Journal Article
Open access
PDF file
SIShunsuke Ishiguro
Shunsuke Ishiguro
TATatsuhiko Aizawa
Tatsuhiko Aizawa
TFTatsuya Funazuka
Tatsuya Funazuka
TSTomomi Shiratori
Tomomi Shiratori
The carbon-supersaturated SKD11 punch was proposed as a green, or, a galling-free, long-life and low energy-consuming forging tool of pure titanium and β-titanium alloy that works with low friction and less work hardening and without galling. The reduction in thickness was increased up to 50% to investigate the friction process on the contact interface and the work-hardening behavior. The nitrogen-supersaturated SKD11 punch was utilized as a reference tool for this forging experiment. Three-dimensional finite element analysis was employed to derive the regression curve between the contact interface width and the friction coefficient. The friction coefficient was estimated in forging the pure titanium wires by using the regression curves. The work-hardening process was analyzed by the hardness mapping on the cross-section of forged wires. The SEM-EDX analysis on the contact interface proved that no adhesion of fresh metallic titanium and titanium oxide debris was seen on the interface between the carbon-supersaturated SKD11 punch and the titanium work. In particular, the work hardening is suppressed without shear localization in forging the β-titanium. Finally, the uniform carbon layer was derived from the supersaturated carbon solute from the punch matrix and wrought as a friction film on the contact interface to reduce the friction and the work hardening as well as suppress the chemical galling. This in situ carbon lubrication must be essential in green forging to highly qualify the titanium and titanium alloy products and to prolong the punch-and-die lives in practical operation.

13 May 2021 in Materials
Verified
Journal Article
Open access
PDF file
TATatsuhiko Aizawa
Tatsuhiko Aizawa
TYTomoaki Yoshino
Tomoaki Yoshino
YSYohei SUZUKI
Yohei SUZUKI
TSTomomi Shiratori
Tomomi Shiratori
A tool steel type SKD11 punch was plasma carburized at 673 K for 14.4 ks at 70 Pa to make carbon supersaturation. This carburized SKD11 punch was employed for upsetting the pure titanium wire with the diameter of 1.00 mm up to the reduction of thickness by 70% in a single shot. Its contact interface to titanium work was analyzed to describe the anti-galling behavior in this forging. Little trace of titanium proved that the galling process was suppressed by the in situ solid lubrication. The isolated free carbon agglomerates are wrought as a solid lubricant to sustain the galling-free forging process. This anti-galling upsetting reduced the residual strains in the forged wires. A long titanium wire with a length of 45 mm was incrementally upset to yield the titanium ribbon with a thickness of 0.3 mm, the width of 2.3 mm, and the length of 50 mm. The grain size of original pure titanium was much reduced to 2 μm on average. A micro-pillared microtexture was imprinted onto this forged titanium ribbon.

30 March 2019 in Metals
Verified
Journal Article
Open access
PDF file
TSTomomi Shiratori
Tomomi Shiratori
TATatsuhiko Aizawa
Tatsuhiko Aizawa
YSYasuo Saito
Yasuo Saito
KWKenji Wasa
Kenji Wasa
Packaging using thermoplastic molding for hollowed GaN chips were requested for a leak-proof micro-joining between plastic molds and copper-based substrates. The design and engineering of micro-textures is a key technology for putting leak-proof packaging into practice. In the present paper, a micro-meshing punch array was prepared using plasma-nitriding-assisted printing. Two-dimensional original patterns were screen-printed onto an AISI316 die substrate and plasma nitrided at 673 K for 14.4 ks (or 4 h). The unprinted surfaces were selectively nitrogen super-saturated to have more nitrogen content than 5 mass% and a higher hardness than 1200 HV. The printed surfaces were selectively sand blasted to fabricate the micro-meshing punch array for micro-embossing. A computer numerically controlled stamping system was utilized to describe the micro-embossing behavior onto copper substrates and to investigate how the micro-textures on the array was transcribed onto the copper. Reduction of takt time as well as flexibility in the micro-grooving were discussed with reference to the picosecond laser machining and mechanical milling processes.

9 January 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
TATatsuhiko Aizawa
Tatsuhiko Aizawa
TYTomoaki Yoshino
Tomoaki Yoshino
YSYohei SUZUKI
Yohei SUZUKI
TSTomomi Shiratori
Tomomi Shiratori
A bare AISI420J2 punch often suffers from severe adhesion of metallic titanium as well as titanium oxide debris particles in dry, cold forging of biomedical titanium alloys. This punch was plasma-carburized at 673 K for 14.4 ks to harden it up to 1200 HV on average and to achieve carbon supersaturation in the carburized layer. This plasma-carburized punch was employed in the cold, dry forging of a pure titanium wire into a flat plate while reducing the thickness by 70%. The contact interface width approached the forged workpiece width with increasing the reduction ratio. This smaller bulging deformation reveals that the workpiece is upset by homogeneous plastic flow with a lower friction coefficient. This low-friction and anti-galling forging process was sustained by an in situ solid lubrication mechanism. Unbound free carbon was isolated from the carbon-supersaturated AISI420J2 matrix and deposited as a thin tribofilm to protect the contact interface from mass transfer of metallic titanium.

17 November 2022 in Micromachines
Verified
Journal Article
Open access
PDF file
TFTatsuya Funazuka
Tatsuya Funazuka
Kuniaki DohdaKuniaki Dohda
Kuniaki Dohda
TSTomomi Shiratori
Tomomi Shiratori
SHSyunsuke Horiuchi
Syunsuke Horiuchi
Ikumu WatanabeIkumu Watanabe
Ikumu Watanabe
To apply conventional forming processes to microscale processing, the influence of size effects caused by material properties and friction effects must be considered. Herein, the effects of tool surface properties, such as punch surface texture, on microextrusion properties, such as extrusion force, product shape, and product microstructure, were investigated using AA6063 billets as test pieces. Millimeter-scale, microscale, and nanoscale textures were fabricated on the punch surfaces. Punch texturing was conducted by electrical discharge machining or polishing or using a laser process. The extrusion force increased rapidly as the stroke progressed for all punch textures. Comparing the product shapes, the smaller the texture size, the lower the adhesion and the longer the backward extrusion length. The results of material analysis using electron backscatter diffraction show that material flowability is improved, and more strain is uniformly applied when a nanoscale-textured punch is used. By contrast, when a mirror punch was used, material flowability decreased, and strain was applied non-uniformly. Therefore, by changing the surface properties of the punch, the tribology between the tool and material can be controlled, and formability can be improved.