Ti-Cu alloys have broad application prospects in the biomedical field due to their excellent properties. The properties of Ti-Cu alloys are strongly dependent on Cu content, microstructures, its Ti₂Cu phase and its preparation process. The aim of this work is to investigate the effect of Cu content on the precipitation behaviors, mechanical and corrosion properties of the as-cast Ti-Cu alloys. The microstructures and phase evolution were characterized by SEM and TEM, and the properties were studied by tensile and electrochemical test. The results show that the volume fraction of Ti₂Cu phase increases with the increase of Cu content. The Ti₂Cu phase presents a variety of microscopic morphologies with different Cu content, such as rod, granular, lath and block shaped. The crystal orientation relationships between the Ti₂Cu and α-Ti matrix in Ti-4Cu and Ti-10Cu alloys are (103)_Ti2Cu//(0[1$\overline{1}$11)_α-Ti, [$\overline{3}$01]_Ti2Cu//[2$\overline{1}\overline{1}$0]_α-Ti, and (103)_Ti2Cu//(0002)_α-Ti, [$\overline{3}$31]_Ti2Cu//[1$\overline{2}$10]_α-Ti, respectively. The tensile strength, Vickers hardness and Young’s modulus of the Ti-Cu alloys increase with the increase of Cu content, whereas the elongation decreases. The fracture morphologies of these alloys reveal ductile, ductile-brittle hybrid, and cleavage brittle mode, respectively. The corrosion resistance of the Ti-Cu alloys in SBF solution can be described as: Ti-4Cu alloy > Ti-10Cu alloy > Ti-7Cu alloy. The volume fraction of Ti₂Cu phases and the “protective barrier” provided by the fine lath Ti₂Cu phases strongly affected the electrochemical performances of the alloys.

The effects of flame remelting on the microstructural features, mechanical properties and dry sliding wear properties of supersonic plasma sprayed NiCrBSi-30 wt-% Mo coating were evaluated. The modified microstructure of the flame remelted coating, such as reduction in micro-defects, decrease in line roughness, laminar architecture elimination and material homogenisation was obtained. The Vickers micro-hardness and elastic modulus measurement showed an enhancement for flame remelted coating. The main wear mechanism of the as-sprayed coating was adhesive/delaminative wear. While the main wear mechanism of the flame remelted coating was adhesive wear. The wear resistance of flame remelted coating surpassed that of the as-sprayed coating and was by far superior to the substrate.

To improve the heat resistance of titanium alloys, the effects of Y content on the precipitation behavior, oxidation resistance and high-temperature mechanical properties of as-cast Ti-5Al-2.75Sn-3Zr-1.5Mo-0.45Si-1W-2Nb-xY (x = 0.1, 0.2, 0.4) alloys were systematically investigated. The microstructures, phase evolution and oxidation scales were characterized by XRD, Laser Raman, XPS, SEM and TEM. The properties were studied by cyclic oxidation as well as room- and high-temperature tensile testing. The results show that the microstructures of the alloys are of the widmanstätten structure with typical basket weave features, and the prior β grain size and α lamellar spacing are refined with the increase of Y content. The precipitates in the alloys mainly include Y₂O₃ and (TiZr)₆Si₃ silicide phases. The Y₂O₃ phase has specific orientation relationships with the α-Ti phase: (002)Y₂O₃ // ($\overline{1}$$\overline{1}$20)_α-Ti, [110]Y₂O₃ // [$\overline{4}$401]_α-Ti. (TiZr)₆Si₃ has an orientation relationship with the β-Ti phase: (02$\overline{2}$$\overline{1}$)(TiZr)₆Si₃ // (011)_β-Ti, [$\overline{1}$2$\overline{1}$6](TiZr)₆Si₃ // [04$\overline{4}$]_β-Ti. The 0.1 wt.% Y composition alloy has the best high-temperature oxidation resistance at different temperatures. The oxidation behaviors of the alloys follow the linear-parabolic law, and the oxidation products of the alloys are composed of rutile-TiO₂, anatase-TiO₂, Y₂O₃ and Al₂O₃. The room-temperature and 700 °C UTS of the alloys decreases first and then increases with the increase of Y content; the 0.1 wt.% Y composition alloy has the best room-temperature mechanical properties with a UTS of 1012 MPa and elongation of 1.0%. The 700 °C UTS and elongation of the alloy with 0.1 wt.% Y is 694 MPa and 9.8%, showing an optimal comprehensive performance. The UTS and elongation of the alloys at 750 °C increase first and then decrease with the increase of Y content. The optimal UTS and elongation of the alloy is 556 MPa and 10.1% obtained in 0.2 wt.% Y composition alloy. The cleavage and dimples fractures are the primary fracture mode for the room- and high-temperature tensile fracture, respectively.

X2CrNi12 ferritic stainless steel has a wide range of application prospects in the railway transportation, construction, and automobile fields due to its excellent properties. The properties of X2CrNi12 ferritic stainless steel can be further improved by cold-rolling and subsequent annealing treatment. The purpose of this work is to investigate the effect of cold-rolling reduction on the microstructure, texture and corrosion properties of the recrystallized X2CrNi12 ferritic stainless steel by using SEM, TEM, EBSD and electrochemical testing technology. The results show that the crystal orientation characteristics of the cold-rolled sheet could be inherited into the annealed sheet. The higher cold-rolling reduction could promote the deformed grains rotating into the {111} orientation, increasing storage energy and driving force for recrystallization, which could reduce the recrystallized grain size. The orientation densities of α-fiber and γ-fiber were low at 50% cold-rolling reduction. After recrystallization annealing, a large number of grains with random orientation could be produced, and the texture strength was weakened. When the cold-rolling reduction rose to 90%, the γ-fiber texture at {111} was strengthened and the α-fibers, particularly the {112} component, were weakened after recrystallisation annealing, which could improve the formability of the steels. The proportions of special boundaries, i.e., low-angle grain boundaries and low-Σ CSL boundaries, among the grain boundary distribution of the recrystallized X2CrNi12 stainless steel were higher when the reduction was 90%, especially when the annealing temperature was 770 °C. Additionally, the proportion of LAGBs and low-Σ CSL boundaries were 53% and 7.43%, respectively, which improves the corrosion resistance of the matrix, showing the best corrosion resistance.