Thibault Demoulin

Mr. Thibault Demoulin

orcid

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2020 in 3D Printing and Additive Manufacturing
Verified
Journal Article
Open access
JBJoris Burger
Joris Burger
ELEna Lloret-Fritschi
Ena Lloret-Fritschi
FSFabio Scotto
Fabio Scotto
TDThibault Demoulin
Thibault Demoulin
LGLukas Gebhard
Lukas Gebhard
RFRobert J. Flatt
Robert J. Flatt
Concrete is a material favored by architects and builders alike due to its high structural strength and its ability to take almost any form. However, to shape concrete structures, heavy-duty formwork is usually necessary to support the fresh concrete while curing. To expand geometrical freedom, three-dimensional (3D) printed concrete formwork has emerged as a field of research. This article presents one possible application, a novel fabrication process that combines large-scale robotic fused deposition modeling 3D printing with simultaneous casting of a fast-hardening, set-on-demand concrete. This fabrication process, known as “Eggshell,” enables the production of nonstandard concrete structures in a material-efficient process. By casting a fast-hardening concrete in a continuous process, lateral pressure exerted by the fresh concrete is kept to a minimum. In this way, a 1.5-mm-thin thermoplastic shell can be used as a formwork, without any additional support. Geometries of different scales are tested in this article to evaluate the feasibility of the Eggshell fabrication process in an architectural context. An array of printing materials are also tested, and several different reinforcement concepts are analyzed. The findings are used to produce a full-scale architectural demonstrator project. This article shows that a wide range of concrete geometries can be produced in a material-efficient fabrication process, paving the way toward mass customization and structural optimization within concrete architecture.

8 July 2020
Verified
Book Chapter
Closed access
PDF file
JBJoris Burger
Joris Burger
ELEna Lloret-Fritschi
Ena Lloret-Fritschi
NTNizar Taha
Nizar Taha
FSFabio Scotto
Fabio Scotto
TDThibault Demoulin
Thibault Demoulin
RFRobert J. Flatt
Robert J. Flatt

11 May 2022 in Materials
Verified
Journal Article
Open access
PDF file
ELEna Lloret-Fritschi
Ena Lloret-Fritschi
EQElia Quadranti
Elia Quadranti
FSFabio Scotto
Fabio Scotto
Lukas FuhrimannLukas Fuhrimann
Lukas Fuhrimann
TDThibault Demoulin
Thibault Demoulin
RFRobert Flatt
Robert Flatt
Concrete construction harms our environment, making it urgent to develop new methods for building with less materials. Structurally efficient shapes are, however, often expensive to produce, because they require non-standard formworks, thus, standard structures, which use more material than is often needed, remain cheaper. Digital fabrication has the potential to change this paradigm. One method is Digital Casting Systems (DCS), where the hydration of self-compacting concrete is controlled on the fly during production, shortening the required setting time and reducing hydrostatic pressure on the formwork to a minimum. This enables a productivity increase for standard concrete production. More importantly, though, it enables a rethinking of formworks, as the process requires only cheap thin formworks, thus, unlocking the possibility to produce optimised structural members with less bulk material and lower environmental cost. While DCS has already proven effective in building structural members, this process faces the challenge of moving into industry. This paper covers the next steps in doing so. First, we present the benchmark and expectations set by the industry. Second, we consider how we comply with these requirements and convert our fast-setting self-compacting mortar mix into a coarser one. Third, we present the next generation of our digital processing system, which moves closer to the industrial requirements in terms of size and the control system. Finally, two prototypes demonstrate how DSC: (a) increases standard bulk production by 50% and (b) can be cast into ultra-thin formworks. We discuss the results and the short-term industrial concerns for efficiency and robustness, which must be addressed for such a system to be fully implemented in industry.

11 November 2016 in Heritage Science
Verified
Journal Article
Open access
PDF file
TDThibault Demoulin
Thibault Demoulin
FGFred Girardet
Fred Girardet
Timothy WanglerTimothy Wangler
Timothy Wangler
GSGeorge W. Scherer
George W. Scherer
RFRobert Flatt
Robert Flatt
Weathering of clay-bearing sandstones does not only depend on material properties but also on the environmental conditions they are exposed to. The same is true for repaired stones, in which the compatibility of the repair mortar should be studied not only in terms of material properties, but also in terms of the climatic conditions it will be subjected, in order to maximize this compatibility. This paper proposes a methodology to quantify the thermal and hygric stresses in clay-bearing sandstones and their repair, based on the measurement of temperature and relative humidity at the surface and at several depths in a repaired and a non-repaired stone, as well as wind-driven rain and absorbed water. This is illustrated by a case study in an historical building. The data are used to quantify the stresses in the materials and to propose possible degradation mechanisms.

18 January 2016 in Materials
Verified
Journal Article
Open access
PDF file
TDThibault Demoulin
Thibault Demoulin
GSGeorge Scherer
George Scherer
FGFred Girardet
Fred Girardet
RFRobert Flatt
Robert Flatt
The magnitude of the thermal stresses that originate in an acrylic-based repair material used for the reprofiling of natural sandstone is analyzed. This kind of artificial stone was developed in the late 1970s for its peculiar property of reversibility in an organic solvent. However, it displays a high thermal expansion coefficient, which can be a matter of concern for the durability either of the repair or of the underlying original stone. To evaluate this risk we propose an analytical solution that considers the viscoelasticity of the repair layer. The temperature profile used in the numerical evaluation has been measured in a church where artificial stone has been used in a recent restoration campaign. The viscoelasticity of the artificial stone has been characterized by stress relaxation experiments. The numerical analysis shows that the relaxation time of the repair mortar, originating from a low T g , allows relief of most of the thermal stresses. It explains the good durability of this particular repair material, as observed by the practitioners, and provides a solid scientific basis for considering that the problem of thermal expansion mismatch is not an issue for this type of stone under any possible conditions of natural exposure.

15 November 2011 in Hyperfine Interactions
Verified
Journal Article
Closed access
PDF file
UWUrsula Wagner
Ursula Wagner
TDThibault Demoulin
Thibault Demoulin
RGRupert Gebhard
Rupert Gebhard
WHWerner Häusler
Werner Häusler
CMCristina Mazzola
Cristina Mazzola
FWFriedrich E. Wagner
Friedrich E. Wagner