Ablative materials are used extensively in the aerospace industry for protection against high thermal stresses and temperatures, an example being glass/silicone composites. The extreme conditions faced and the cost-risk related to the production/operating stage of such high-tech materials indicate the importance of detecting any anomaly or defect arising from the manufacturing process. In this paper, two different non-destructive testing techniques, namely active thermography and ultrasonic testing, have been used to detect a delamination in a glass/silicone composite. It is shown that a frequency modulated chirp signal and pulse-compression can successfully be used in active thermography for detecting such a delamination. Moreover, the same type of input signal and post-processing can be used to generate an image using air-coupled ultrasound, and an interesting comparison between the two can be made to further characterise the defect.
The use of different spectral bands in the inspection of artworks is highly recommended to identify the maximum number of defects/anomalies (i.e., the targets), whose presence ought to be known before any possible restoration action. Although an artwork cannot be considered as a composite material in which the zero-defect theory is usually followed by scientists, it is possible to state that the preservation of a multi-layered structure fabricated by the artist’s hands is based on a methodological analysis, where the use of non-destructive testing methods is highly desirable. In this paper, the infrared thermography and hyperspectral imaging methods were applied to identify both fabricated and non-fabricated targets in a canvas painting mocking up the famous character “Venus” by Botticelli. The pulse-compression thermography technique was used to retrieve info about the inner structure of the sample and low power light-emitting diode (LED) chips, whose emission was modulated via a pseudo-noise sequence, were exploited as the heat source for minimizing the heat radiated on the sample surface. Hyper-spectral imaging was employed to detect surface and subsurface features such as pentimenti and facial contours. The results demonstrate how the application of statistical algorithms (i.e., principal component and independent component analyses) maximized the number of targets retrieved during the post-acquisition steps for both the employed techniques. Finally, the best results obtained by both techniques and post-processing methods were fused together, resulting in a clear targets map, in which both the surface, subsurface and deeper information are all shown at a glance.
The use of pulse-compression in ultrasonic non-destructive testing has assured, in various applications, a significant improvement in the signal-to-noise ratio. In this work, the technique is combined with linear phased array to improve the sensitivity and resolution in the ultrasonic imaging of highly attenuating and scattering materials. A series of tests were conducted on a 60 mm thick carbon fiber reinforced polymer benchmark sample with known defects using a custom-made pulse-compression-based phased array system. Sector scan and total focusing method images of the sample were obtained with the developed system and were compared with those reconstructed by using a commercial pulse-echo phased array system. While an almost identical sensitivity was found in the near field, the pulse-compression-based system surpassed the standard one in the far-field producing a more accurate imaging of the deepest defects and of the backwall of the sample.
26 July 2019 in Journal of Nondestructive Evaluation
Ultrasonic pulse-echo non-destructive testing, combined with Distance Gain Size (DGS) analysis, is still the main method used for the inspection of forgings such as shafts or discs. This method allows the inspection to be carried out, assuring in turns the necessary sensitivity and defect detection capability in most of the cases. However, when testing large or highly attenuating samples with standard pulse-echo, the maximum achievable signal-to-noise ratio is limited by both the beam energy physical attenuation during the propagation and by the inherent divergence of any ultrasound beam emitted by a finite geometrical aperture. To face this issue, the application of the pulse-compression technique to the ultrasonic inspection of forgings was proposed by some of the present authors, in combination with the use of broadband ultrasonic transducers and broadband chirp excitation signals. Here, the method is extended by applying DGS analysis to the pulse-compression output signal. Both standard single-frequency/narrowband DGS and multi-frequency/broadband DGS analyses applied on pulse-compression data acquired on a forging with known defects are tested and compared. It is shown that the DGS analysis works properly with pulse-compression data collected by using a separate transmitter and receiver transducers. Narrowband analysis and broadband analyses provide almost identical results, but the latter exhibits advantages over the traditional method: it allows the inspection frequency to be optimized by using a single pair of transducers and with a single measurement. In addition, the range resolution achieved is higher than the one achievable for the narrowband case.
Pulse compression applied to the signal processing in NDT inspections has shown significant improvement in the signal-to-noise-ratio of the measurements. The sensitivity of ultrasonic phased array measurements is enhanced when combined with pulse compression procedures. In this work, pulse compression has been implemented to linear array transducers, while using frequency modulated, chirp excitation signals. A system of signal generation and acquisition has specifically been designed for the realization of the proposed phased array inspection system based on pulse compression. A reference aluminum sample with known flat bottom holes was inspected with the proposed system. The spatial and lateral resolutions obtained from Sector B-scan images demonstrate the quality of defect detection and characterization.