The hydrodynamic pattern, which surrounds the pier near a splitter that has T-shape, is investigated by adopting a numerical method and using ANSYS Fluent Software to achieve computation. The essential objective of this paper refers to revealing the behavior of the hydrodynamic field around the...
28 November 2022 in U.Porto Journal of Engineering
This paper intends to numerically analyze the hydrodynamic characteristics of the flow pattern that surrounds the circular pier near the vane angle. These include flow velocity, turbulent intensity, and pressure. A computational fluid dynamic is proposed to simulate the two-dimensional model by using the finite volume method, while the k - ε turbulence model is used to describe the turbulent model. The vane is located upstream of the pier, with its dimensions as function of the pier diameter. The distance between the vane and the pier center is equal to the pier diameter, the angle of the vane is put with a range from 60o to 180o, and the pier diameter is equal to 10 mm. The turbulent flow has a Reynolds number that varies from 20000 to 50000. The existence of the vane angle leads to two different processes, which are flow separation and flow dissipation, which have a direct effect on flow velocity, turbulent intensity, and pressure. From the current numerical results, the relationships between Reynolds number and average flow velocity, maximum flow velocity, turbulent intensity, and maximum turbulent intensity are more sensitive to flow separation and flow dissipation along the vane. Also, positive and negative pressure distributions have a higher influence on flow separation and flow dissipation.
20 January 2024 in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
The Spalart-Allmaras turbulence model is used to study the flow patterns around a semi-circular cylinder surrounded by water in two dimensions with various angles of strike owing to rotating the cylinder by an angle. The rotation angle ranges from zero to 360° and the ANSYS Fluent software is employed to implement the required simulation. The Spalart-Allmaras turbulence model is used to determine the flow velocity vector, velocity contours, and pressure contours. Moreover, this turbulent model is used to calculate three different non-dimensional parameters, the drag coefficient, lift coefficient, and skin friction factors. Two different Reynolds numbers (Re) are adopted in the calculation of the three non-dimensional parameters with various values for the angle of the cylinder rotation. Here, the semi-circular cylinder is considered stationary but it is placed in a water domain in various positions. Due to the scarcity in information about using the Spalart-Allmaras turbulence model as compared with other models, which are widely used to investigate the flow around the cylinder, three turbulent models are employed to verify the results obtained by the Spalart-Allmaras model, these models are (standard), (RNG), and (Realizable). Results show an excellent agreement between the four turbulent models compared, where there is no significant variation in the obtained results, all results are very similar.
30 June 2022 in Eastern-European Journal of Enterprise Technologies
The anisotropy of metals is an important property that has a significant impact on the dimensional accuracy of components in manufacturing. In metal forming processes significant attention has been given to multilayer composite sheets as they may combine the advantages of materials with various mechanical properties. In this study, the effect of anisotropy is investigated in the process of single point incremental forming (SPIF) of aluminum bilayer sheets. The finite element method (FEM) is used to study the effect of layer arrangement and the anisotropy of metal sheets relative to the rolling direction. For the effective description of sheet metal anisotropy, the two-dimensional Yld2000-2D yield function is implemented in Abaqus software using a material subroutine (VUMAT). The calculation and calibration of the coefficients of Yld2000-2D in accordance with the experimental data were performed using a MATLAB code. For comparison, the anisotropic coefficients of Yld2000-2D were replaced by unit values in the same VUMAT to investigate forming behavior in the isotropic case with the von Mises yield function. Anisotropic and isotropic models are compared in a conical geometry by assessing equivalent plastic strain, sheet thickness, and forming tool reaction forces. Our findings show that anisotropy of sheet metal causes less variation in material properties compared to the isotropic case, significantly affecting the stiffness and, subsequently, the final shape dimensional accuracy of the formed component. The results of the study have a practical application in that they can be used to identify strategies for anisotropic bimetal sheets to improve such material forming processes
The interaction between the hydrodynamic field around the pier and the hydrodynamic field around the vane represents a challenge to the hydraulic designers owing to the high risk that must be considered, especially the alteration in flow velocity and pressure distribution. The problem statement, reveal how the vane redistributes the local pressures around pier under varied vane length moreover we seek about how the variation in the values of Reynolds number has significant impact on the distribution of local pressures. The paper focuses on the numerical simulation of the hydrodynamic field between the vane and the circular pier in two dimensions for steady, incompressible and laminar water flow over a fixed and horizontal bed by using ANSYS Fluent software. The simulation relies on different Reynolds numbers and different vanes lengths. The length and thickness of the vane are described as a function of the pier diameter, while the distance between the vane and the pier has been taken to be equal to the pier diameter. The hydrodynamic field is defined by local static pressure, local dynamic pressure and pressure coefficient. These variables are studied numerically around the pier circumference by depending on an angle measured from the pier centre to any point on the pier circumference. It is found that the variation in these variables with angle based on pressure distribution, velocity distribution, flow separation and flow dissipation, as well as the vane length, has a vital role in determining the hydraulic behaviour of the hydraulic system. The purpose of the paper concentrates on how the vane alter the hydrodynamic features around the pier.
21 November 2022 in Journal of Thermal Engineering
Modern engineering challenges require the world to use renewable and environmentally friendly energy. One of the most important forms of renewable energy is solar energy. The parabolic collector is a popular collector used to absorb solar energy. In this study, a new approach is used to calculate the radiation concentration ratio in a parabolic collector. The concentration ratio is calculated from the ratio of the reflection beam to the incident beam radiation, and it depends on two main variables: the collector width (W) and the focal length (P). The model is tested and compared to results from previously published work. The comparison showed that the model results can be relied upon for accuracy and are compatible with published results. The results indicate that increasing the width of the collector (W) leads to an increase in the concentration ratio (RC), while the contrary is true when the focal length (P) increased. The collector efficiency minimum values were 19.3%, 21.07 %, 22.35% and 23.33% at concentration ratios of 69, 80, 103 and 148 in line with the focus length values of 0.6m, 0.7m, 0.8m and 0.9m, respectively. The developed model is applied according to the conditions of Basra, Iraq (47.78o longitude and 30.5o latitude).