Mohammad Askari

Dr. Mohammad Askari

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 October 2021 in Agriculture
Verified
Journal Article
Open access
PDF file
MAMohammad Askari
Mohammad Askari
Yousef Abbaspour-GilandehYousef Abbaspour-Gilandeh
Yousef Abbaspour-Gilandeh
Ebrahim TaghinezhadEbrahim Taghinezhad
Ebrahim Taghinezhad
Ahmed El ShalAhmed El Shal
Ahmed El Shal
Rashad HegazyRashad Hegazy
Rashad Hegazy
Mahmoud OkashaMahmoud Okasha
Mahmoud Okasha
This study aimed to evaluate the ability of the response surface methodology (RSM) approach to predict the tractive performance of an agricultural tractor during semi-deep tillage operations. The studied parameters of tractor performance, including slippage (S), drawbar power (DP) and traction efficiency (TE), were affected by two different types of tillage tool (paraplow and subsoiler), three different levels of operating depth (30, 40 and 50 cm), and four different levels of forward speed (1.8, 2.3, 2.9 and 3.5 km h−1). Tractors drove a vertical load at two levels (225 kg and no weight) in four replications, forming a total of 192 datapoints. Field test results showed that all variables except vertical load, and different combinations of this and other variables, were effective for the S, DP and TE. Increments in speed and depth resulted in an increase and decrease in S and TE, respectively. Additionally, the RSM approach displayed changes in slippage, drawbar power and traction efficiency, resulting from alterations in tine type, depth, speed and vertical load at 3D views, with high accuracy due to the graph’s surfaces, with many small pixels. The RSM model predicted the slippage as 6.75%, drawbar power as 2.23 kW and traction efficiency as 82.91% at the optimal state for the paraplow tine, with an operating depth of 30 cm, forward speed of 2.07 km h−1 and a vertical load of 0.01 kg.

3 January 2024 in Heliyon
Verified
Journal Article
Open access
ALArash Lajani
Arash Lajani
ANAli Mohammad Nikbakht
Ali Mohammad Nikbakht
MAMohammad Askari
Mohammad Askari
MSMahmood Reza Salar
Mahmood Reza Salar
A clear understanding of soil-machine interaction is utilised in many areas, such as rational design and performance optimisation of soil-engaging tools/implements. This research developed a new soil bin to investigate the interaction between soil-narrow tines and soil failure. The new soil bin consisted of a chassis, a bin, a variable speed carriage and a bolt and nut type power transmission system between the motor and carriage. The design criteria of the new soil bin were based on the drive system's immediate acceleration of the carriage unit. A curved chisel tine was tested to evaluate the system's capabilities. Three parameters, including lift height, failure side area and forward failure distance, were investigated at two forward speeds of 0.037 and 0.05 m/s and three rake angles of 5°, 10° and 20°. An analysis of variance (ANOVA) test revealed the effect of rake angle on the lift height, failure side area, and forward failure distance was significant (P < 0.01). However, the forward speed did not have any significant influence on parameters. Also, the lift height and failure side area increased significantly (P < 0.01) by increasing the rake angle, while the forward failure distance decreased. Regarding soil failure, the results were in harmony with Godwin and Spoor's model. The regression and ANFIS models were developed to predict the output parameters by considering input parameters. The R2 values and ANFIS models were 0.4895, 0.7264, 0.9856, and 0.9999, 1, 1, respectively, for lift height, side area, and forward distance. Therefore, ANFIS approach was more accurate for predicting soil failure parameters.

27 January 2025 in Applied and Environmental Soil Science
Verified
Journal Article
Open access
DKDavood Kalantari
Davood Kalantari
MAMohammad Askari
Mohammad Askari
SMSeyed Reza Mousavi-Seyedi
Seyed Reza Mousavi-Seyedi
NANezamedin Asadi
Nezamedin Asadi
Agricultural soil compaction caused by tractors and heavy farm machines has a direct impact on farm productivity. Therefore, the effect of influencing parameters on soil compaction was studied and evaluated using a wheel tester device in the soil bin environment. Experiments were carried out at 3 levels of vertical load (170, 250, and 320 kg), 3 levels of tire inflation pressure (10, 15, and 20 psi), 3 levels of soil moisture content (2%, 7%, and 13% wet basis), and 2 levels of forward speed (0.386 and 0.879 km/h) in the form of a factorial design and a randomized complete block design in 3 replications. Next, soil compaction was predicted under the influence of investigated parameters using ANFIS. The results showed that the advance of the wheel at low speed and high soil moisture content significantly increases soil compaction. The present findings showed that the soil compaction increases linearly with the relative increase of the vertical load on the tire. Meanwhile, the relative increase of soil compaction in wet soil (7%–13% relative humidity, wb) was relatively 9.93 times higher than the soil compaction in low humidity (2%–7%). The results also show that reducing tire inflation pressure from 20 to 15 psi reduces soil compaction by 12.94%. The correlation coefficient between the measured and predicted data using ANFIS for soil compaction was equal to 1, which showed the high accuracy of ANFIS models in predicting the studied parameters. This approach provides criteria for a more appropriate selection of agricultural tires.

27 April 2026 in Scientific Reports
Verified
Journal Article
Open access
PDF file
HSHossein Shaebani Sheshpoli
Hossein Shaebani Sheshpoli
MAMohammad Askari
Mohammad Askari
DKDavood Kalantari
Davood Kalantari
The purpose of this study is to investigate the effects of forward speed, soil moisture content, disc type and disc gang angle on soil disturbance area caused by a four-disc harrow in a soil bin. Moreover, the study aims to predict and optimize the soil disturbance area with considering the input variables to obtain the goals of conservation tillage. The input variables included forward speed (6.43 and 13.15 m/min), soil moisture content (5.37% and 13.25% (db)), disc type (plain and notched), and disc gang angle (0, 15 and 30°). Output variable was soil disturbance area which was measured using profile meter. A total of 72 tests were run based on randomized complete block design (RCBD). Test data were used to develop the regression, artificial neural network (ANN), and response surface methodology (RSM) models and their accuracy were compared. Furthermore, RSM approach was used for optimization process. Results indicated that soil disturbance area was significantly affected by disc gang angle (P < 0.01), the interaction between moisture and angle (P < 0.05), and speed and angle (P < 0.01). Increasing the angle from 0 to 15 and 30° substantially enhanced disturbance area (115.1, 222.1, and 337.7 cm², respectively). Regression, ANN and RSM models predicted the disturbance area of notched discs with higher accuracy (R2 = 0.8891, 0.9666 and 0.9696, respectively) than plain discs (R2 = 0.7747, 0.9356 and 0.8826, respectively). The optimization process for disturbance area were obtained 280.814 and 295.710 cm2 for equal moisture content of 9.31%, forward speed of 8.82 and 7.282 m/min and disc gang angle of 22.57 and 23.935° with equal desirability of 1.000 for plain and notched discs, respectively. Among the input variables under investigation, the angle of the plate group was the most effective on soil disturbance area. The best studied prediction approach was RSM for disturbance area of notched discs with highest R2 (0.9696). The obtained advantages of RSM approach relative to ANN and regression ones in this project are listed as higher accuracy in prediction of soil disturbance area, 3D surface curves in RSM output help readers to better understand the changes in the output parameter under the influence of the input parameters, they can also help researchers to obtain the output parameter in the unmeasured input parameters. Moreover, the optimization process could be done only using RSM. The RSM approach was able to obtain the optimal values of the input variables with a very high desirability (1.000) in order to idealize the soil disturbance rate.