Optical printing holds great potential to enable the use of the vast variety of colloidal nanoparticles (NPs) in nano- and microdevices and circuits. By means of optical forces, it enables the direct assembly of NPs, one by one, onto specific positions of solid surfaces with great flexibility of pattern design and no need of previous surface patterning. However, for unclear causes it was not possible to print identical NPs closer to each other than 300 nm. Here, we show that the repulsion restricting the optical printing of close by NPs arises from light absorption by the printed NPs and subsequent local heating. By optimizing heat dissipation, it is possible to reduce the minimum separation between NPs. Using a reduced graphene oxide layer on a sapphire substrate, we demonstrate for the first time the optical printing of Au—Au NP dimers. Modeling the experiments considering optical, thermophoretic, and thermo-osmotic forces we obtain a detailed understanding and a clear pathway for the optical printing fabrication of complex nano structures and circuits based on connected colloidal NPs.
Despite the increasing economic incentives and environmental advantages associated to their substitution, carbon-rich fossil fuels are expected to remain as the dominant worldwide source of energy through at least the next two decades and perhaps later. Therefore, both the control and reduction of CO2 emissions have become environmental issues of major concern and big challenges for the international scientific community. Among the proposed strategies to achieve these goals, conversion of CO2 by its reduction into high added value products, such as methane or syngas, has been widely agreed to be the most attractive from the environmental and economic points of view. In the present work, thermocatalytic reduction of CO2 with H2 was studied over a nanostructured ceria-supported nickel catalyst. Ceria nanocubes were employed as support, while the nickel phase was supported by means a surfactant-free controlled chemical precipitation method. The resulting nanocatalyst was characterized in terms of its physicochemical properties, with special attention paid to both surface basicity and reducibility. The nanocatalyst was studied during CO2 reduction by means of Near Ambient Pressure X-ray Photoelectron Spectroscopy (NAP-XPS). Two different catalytic behaviors were observed depending on the reaction temperature. At low temperature, with both Ce and Ni in an oxidized state, CH4 formation was observed, whereas at high temperature above 500 °C, the reverse water gas shift reaction became dominant, with CO and H2O being the main products. NAP-XPS was revealed as a powerful tool to study the behavior of this nanostructured catalyst under reaction conditions.
Supported Pd/CeO2 catalytic systems have been widely investigated in the low-temperature oxidation of CO (LTO CO) due to the unique oxygen storage capacity and redox properties of the ceria support, which highly influence the structural, chemical and electronic state of Pd species. Herein, operando near-ambient pressure XPS (NAP-XPS) technique has allowed the study of a conventional Pd/CeO2 catalyst surface during the CO oxidation reaction under experimental conditions closer to the actual catalytic reaction, unfeasible with other surface science techniques that demand UHV conditions. SEM, HRTEM and XRD analyses of the powder catalyst, prepared by conventional incipient wetness impregnation, reveal uniformly CeO2-loaded Pd NPs of less than 2 nm size, which generated an increase in oxygen vacancies with concomitant ceria reduction, as indicated by H2-TPR and Raman measurements. Adsorbed peroxide (O22−) species on the catalyst surface could also be detected by Raman spectra. Operando NAP-XPS results obtained at the ALBA Synchrotron Light Source revealed two kinds of Pd species under reaction conditions, namely PdOx and PdII ions in a PdxCe1−xO2−δ solution, the latter one appearing to be crucial for the CO oxidation. By means of a non-destructive depth profile analysis using variable synchrotron excitation energies, the location and the role of these palladium species in the CO oxidation reaction could be clarified: PdOx was found to prevail on the upper surface layers of the metallic Pd supported NPs under CO, while under reaction mixture it was rapidly depleted from the surface, leaving a greater amount in the subsurface layers (7% vs. 12%, respectively). On the contrary, the PdxCe1−xO2−δ phase, which was created at the Pd–CeO2 interface in contact with the gas environment, appeared to be predominant on the surface of the catalyst. Its presence was crucial for CO oxidation evolution, acting as a route through which active oxygen species could be transferred from ceria to Pd species for CO oxidation.
Compositional changes taking place during the synthesis of alloyed CdSeZnS nanocrystals (NCs) allow shifting the optical features to higher energy as the NCs grow. Under certain synthetic conditions, the effect of those changes on the surface/interface chemistry competes with and dominates over the conventional quantum confinement effect in growing NCs. These changes, identified by means of complementary advanced spectroscopic techniques such as XPS (X-ray Photoelectron Spectroscopy) and XAS (X-ray absorption Spectroscopy), are understood in the frame of an ion migration and exchange mechanism taking place during the synthesis. Control over the synthetic routes, during the NCs growth, represents an alternative tool to tune the optical properties of colloidal quantum dots, broadening the versatility of the wet-chemical methods.
We present a biomimetic electrochemical sensor for glyphosate (GLY) detection, utilizing graphite electrodes modified with electropolymerized copper(II) meso-tetra(4-sulfonatophenyl)porphyrin (CuP). The Cu(II) centers provide dual functionality: catalytic oxygen reduction and selective GLY coordination, which leads to a proportional suppression of redox currents. Characterization (SEM-EDS/Raman/UV-Vis) confirmed CuP polymerization and specific GLY binding. The sensor achieved a 1 μmol L−1 detection limit (S/N = 3) with linear response (2–120 μmol L−1; RSD = 0.7%) and >98% recovery in spiked rainwater. Stability tests showed 99% signal retention after 30 days, outperforming enzyme-based sensors. This platform combines three key advantages: (1) sustainable fabrication ($0.12/electrode), (2) rapid analysis (<5 min per sample), and (3) field-deployability without instrumentation. The nanostructured CuP film improves sensitivity and contributes to selective GLY detection by excluding common interferents (nitrate/humic acid). Compared to chromatographic methods, this approach offers an eco-friendly alternative for environmental GLY monitoring.