This paper describes a study on the improvement of the dehydration performance of the conventional washing machine model. Recently, as interest in improving the dehydration performance of washing machines has increased, the need for a study on a high-speed electric motor has emerged. However, this conventional spoke-type PMSM has difficulty in speeding up due to the following problems. First, field weakening control is indispensable for high-speed operation of an electric motor. This control method is a big problem in causing torque drop and irreversible demagnetization of the motor. Moreover, the centrifugal force increases during high-speed operation, which adversely affects the stiffness of the motor. Therefore, in this paper, a new rotor shape of spoke-type PMSM was proposed to solve the above problem.

In this paper, an axial slot-less permanent magnet synchronous motor (ASFPMSM) was designed to increase the power density. The iron core of the stator was replaced with block coils, and the stator back yoke was removed because 3D printing can provide a wide range of structures of the stator. The proposed model also significantly impacts efficiency because it can reduce iron loss. To meet size and performance requirements, coil thickness and number of winding layers in the block, the total amount of magnet, and pole/slot combinations were considered. The validity of the proposed model was proved via finite elements analysis (FEA).

The spoke-type permanent magnet synchronous motor (PMSM), which is a general ferrite magnetic flux-concentrated motor, has a low portion of reluctance torque at the total torque magnitude. Therefore, as a way to increase the reluctance torque, there is a double-layer spoke-type PMSM that can maximize the difference in inductance between the d-axis and the q-axis. However, in the double-layer spoke-type PMSM, cogging torque, torque ripple, and total harmonic distortion (THD) increase with reluctance torque, which is the main cause of vibration and noise. In this paper, a method is proposed that provides the same effect as skew without dividing stages of the permanent magnet by dividing the core of the rotor into two types so that it is easy to manufacture according to the number of stages, unlike extant skew methods. Based on the method, the reduction in cogging torque and THD was verified by finite element analysis (FEA).

Demand for high-speed motors is increasing. Surface-mounted permanent magnet synchronous motors (SPMSM) used in high-speed applications have magnets attached to the rotor, so there is a risk of damage and scattering due to centrifugal force as the speed increases. For this reason, applying the retaining sleeve to the rotor is essential. However, when using sleeves, there is a problem of reducing efficiency due to eddy current loss. In this paper, a study was conducted on a motor for a 100 kW building air conditioning system operating at a speed of 20,000 rpm. The purpose of the study is to reduce eddy current loss by optimizing the sleeve geometry. To this end, 3D finite element analysis (FEA) using JMAG 22.1 was conducted to analyze eddy current loss, the minimum safety factor was analyzed through mechanical stiffness analysis using ANSYS Workbench, and the validity of sleeve shape was proved through cause analysis. Through the research results, it is expected that the shape change of the sleeve will have the effect of reducing eddy current loss.

Permanent magnet synchronous motors (PMSMs) are highly affected by magnetization, which determines the magnetization level in the permanent magnet (PM). There are three main magnetization methods: single-unit, stator coil, and post-assembly magnetization. Post-assembly magnetization is widely used in PMSM mass production due to its ability to achieve high magnetization performance using a separate magnetizing yoke. However, spoke-type PMSMs with ferrite PMs face challenges when using the post-assembly method. The structural configuration of two magnets located radially hampers effective magnetized field transmission to the rotor’s interior due to the narrow space between the magnets. Maximizing the magnetization rate becomes crucial, but the limited space in the spoke-type structure complicates this. This paper addresses the issue and analyzes factors influencing post-assembly magnetization characteristics. A novel yoke structure is proposed, reducing the distance between the coil and magnet, leading to more efficient magnetization. The parametric and performance comparative analysis shows an impressive 17.1%_p increase in magnetization rate with the proposed yoke structure compared to the existing yoke. This outcome contributed to a solution for enhancing the magnetization performance of spoke-type ferrite PMSMs.