This study examined the use of waste plastic oil (WPO) combined with biodiesel as an alternative fuel for diesel engines, also commonly known as compression ignition engines, and focused on comparison of the basic physical and chemical properties of fuels, engine performance, combustion characteristics, and exhaust emissions. A preliminary study was conducted to determine the suitable ratio for the fuel blends in consideration of fuel lubricity and viscosity, and these results indicated that 10% biodiesel—derived from either palm oil or castor oil—in waste plastic oil was optimal. In addition, characterization of the basic properties of these fuel blends revealed that they had higher density and specific gravity and a lower flash point than diesel fuel, while the fuel heating value, viscosity, and cetane index were similar. The fuel blends, comprised of waste plastic oil with either 10% palm oil biodiesel (WPOP10) or 10% castor oil biodiesel (WPOC10), were selected for further investigation in engine tests in which diesel fuel and waste plastic oil were also included as baseline fuels. The experimental results of the performance of the engine showed that the combustion of WPO was similar to diesel fuel for all the tested engine loads and the addition of castor oil as compared to palm oil biodiesel caused a delay in the start of the combustion. Both biodiesel blends slightly improved brake thermal efficiency and smoke emissions with respect to diesel fuel. The addition of biodiesel to WPO tended to reduce the levels of hydrocarbon- and oxide-containing nitrogen emissions. One drawback of adding biodiesel to WPO was increased carbon monoxide and smoke. Comparing the two biodiesels used in the study, the presence of castor oil in waste plastic oil showed lower carbon monoxide and smoke emissions without penalty in terms of increased levels of hydrocarbon- and oxide-containing nitrogen emissions when the engine was operated at high load.

Waste plastic oil (WPO) derived from pyrolysis of plastic debris and municipal waste is one of the promising alternative fuels because of its similar carbon chain characteristics and physical properties to diesel fuel. WPO also contains naphtha which is gasoline-like and may not be well-suited to a diesel engine. Technically, naphtha should be eliminated from WPO by distillation, and the resulting product is called distilled waste plastic oil (WPOD). This work experimentally investigates the influences of these fuels burned in a diesel engine on combustion characteristics and exhaust gas emissions. Both WPO and WPOD fuels contribute to the larger amount of nitrogen oxides than diesel fuel. Carbon-based emissions increase when the engine operates with these pyrolysis fuels by retarding the ignition onset of their combustion occurrences. Meanwhile, their shorter-carbon-chain links provide a lower smoke index. However, brake thermal efficiency and brake specific fuel consumption are beneficial because of their high calorific value and cetane index.

This study investigates the viability of using plastic oils derived from High-density polyethylene (HDPE), Polypropylene (PP), and Polystyrene (PS) as alternative fuels for diesel engines. The research focuses on comparing the physical and chemical properties, fuel lubricity, engine performance, combustion characteristics, and exhaust emissions of these plastic oils. Analysis revealed that PS exhibits different fuel properties compared to diesel, with a carbon range distribution similar to gasoline, while HDPE and PP properties closely resemble diesel fuel. To prevent potential engine damage, PS was excluded from engine tests. PP displayed the best fuel lubricity, attributed to its higher kinematic viscosity and sulphur content, reducing direct friction. Diesel followed, with PS and HDPE in decreasing order of lubricity. Diesel's lubricity was influenced by the 7% palmitic methyl ester content in the fuel. In engine tests, HDPE demonstrated BTE similar to diesel, while PP exhibited lower BTE due to combustion retardation, leading to increased energy losses and higher BSFC. The combustion characteristics, in-cylinder pressure, and heat release rate of HDPE closely resembled diesel, while PP showed significantly delayed combustion due to low oxygen content and higher kinematic viscosity. Notably, NO_X emissions from PP were lower than diesel and HDPE at all engine loads due to heat losses, resulting in a low in-cylinder temperature unsuitable for NO_X emission. HDPE produced higher NO_X emissions than diesel at low and middle loads due to its higher H/C ratio, promoting high thermal NO_X formation. HC emissions from both HDPE and PP were higher than diesel due to increased fuel supply, hindering chemical bond breakdown. Similarly, CO emissions increased for HDPE and PP due to insufficient time for complete combustion, with HDPE producing more CO due to its heavy composites and lower cetane index. Smoke emissions from both HDPE and PP surpassed diesel, attributed to lower oxygen and higher sulphur content, leading to increased sulphurate particulate matter formation, and lower fuel density referring to the high amount of fuel supplied to the engine.

This work presented the influence of metal oxides as the support for silver-supported catalysts on the catalytic oxidation of diesel particulate matter (DPM). The supports selected to be used in this work were CeO₂ (reducible), ZnO (semiconductor), TiO₂ (reducible and semiconductor), and Al₂O₃ (acidic). The properties of the synthesized catalysts were investigated using XRD, TEM, H₂-TPR, and XPS techniques. The DPM oxidation activity was performed using the TGA method. Different states of silver (e.g., Ag° and Ag⁺) were formed with different concentrations and affected the performance of the DPM oxidation. Ag₂O and lattice oxygen, which were mainly generated by Ag/ZnO and Ag/CeO₂, were responsible for combusting the VOCs. The metallic silver (Ag°) formed primarily on Ag/Al₂O₃ and Ag/TiO₂ was the main component promoting soot combustion. Contact between the catalyst and DPM had a minor effect on VOC oxidation but significantly affected the soot oxidation activity.

In the present work, an experimental investigation is carried out on the use of waste plastic oil produced from waste poly(ethylene terephthalate) (PET) bottles (WPOB) as an alternative fuel for diesel engines. The physical and chemical properties of WPOB were analyzed, and it was found that it has fuel properties similar to those of petroleum fuels. The WPOB was tested in a diesel engine to evaluate the effect of WPOB on combustion and emissions characteristics. In addition, particulate matter (PM) emissions generated by the combustion of WPOB were analyzed. The combustion of WPOB was retarded with respect to diesel fuel, resulting in higher carbon-based emissions. The thermogravimetric analysis (TGA) results show that the temperature to reach the maximum rate of soot oxidation was lower with WPOB combustion. Because of the significant delay at the start of combustion and increase in emissions, the direct use of WPOB in the diesel engine is not recommended. It is suggested that WPOB can be used as a blend component to reduce the amount of diesel fuel used in diesel engines. Thus, further study on the effect of diesel fuel blended with WPOB on the combustion and emissions characteristics was performed. The results reveal that the maximum WPOB present in diesel fuel to avoid the increase in carbon-based emissions is 20% by volume to keep combustion and emissions characteristics similar to those of diesel fuel.