This study examined the use of waste plastic oil (WPO) combined with biodiesel as an alternative fuel for diesel engines, also commonly known as compression ignition engines, and focused on comparison of the basic physical and chemical properties of fuels, engine performance, combustion characteristics, and exhaust emissions. A preliminary study was conducted to determine the suitable ratio for the fuel blends in consideration of fuel lubricity and viscosity, and these results indicated that 10% biodiesel—derived from either palm oil or castor oil—in waste plastic oil was optimal. In addition, characterization of the basic properties of these fuel blends revealed that they had higher density and specific gravity and a lower flash point than diesel fuel, while the fuel heating value, viscosity, and cetane index were similar. The fuel blends, comprised of waste plastic oil with either 10% palm oil biodiesel (WPOP10) or 10% castor oil biodiesel (WPOC10), were selected for further investigation in engine tests in which diesel fuel and waste plastic oil were also included as baseline fuels. The experimental results of the performance of the engine showed that the combustion of WPO was similar to diesel fuel for all the tested engine loads and the addition of castor oil as compared to palm oil biodiesel caused a delay in the start of the combustion. Both biodiesel blends slightly improved brake thermal efficiency and smoke emissions with respect to diesel fuel. The addition of biodiesel to WPO tended to reduce the levels of hydrocarbon- and oxide-containing nitrogen emissions. One drawback of adding biodiesel to WPO was increased carbon monoxide and smoke. Comparing the two biodiesels used in the study, the presence of castor oil in waste plastic oil showed lower carbon monoxide and smoke emissions without penalty in terms of increased levels of hydrocarbon- and oxide-containing nitrogen emissions when the engine was operated at high load.

The characterization of pyrolysis oil obtained from mixed waste plastics and its utilization in a compression ignition engine were investigated. The chemical compositions and physicochemical properties of distilled waste plastic oil (WPO) and crude waste plastic oil (CWPO) were analyzed. The experiment was conducted with a variable compression ratio diesel engine at various loads and compression ratios to evaluate combustion characteristics, exhaust emissions, and engine performance. The experimental results show that CWPO contains the highest percentage of carbon atoms in the C4–C11 group, while WPO contains the highest percentage of carbon atoms in the C12–C20 group, similar to the main compositions of diesel fuel. According to the preliminary study in chemical compositions and physicochemical properties, WPO and diesel fuel were selected for the engine test at different compression ratios of 16, 17, and 18 and different engine operating loads of 25%, 50%, and 75% of maximum engine torque at an engine speed of 1500 rpm. It was found that increasing the engine operating load and the compression ratio tends to increase the brake thermal efficiency. Increasing the compression ratio results in a significantly shorter delay time in a combustion state. A lower cetane index and a higher percentage of long chain carbon compounds (C12–C20) could be the main factors affecting higher NOx, CO, and HC emissions with the combustion characteristics of WPO, compared to diesel fuel. The disadvantage of emissions by the use of WPO can be alleviated when the engine is running at maximum load and a high compression ratio.

In the present work, an experimental investigation is carried out on the use of waste plastic oil produced from waste poly(ethylene terephthalate) (PET) bottles (WPOB) as an alternative fuel for diesel engines. The physical and chemical properties of WPOB were analyzed, and it was found that it has fuel properties similar to those of petroleum fuels. The WPOB was tested in a diesel engine to evaluate the effect of WPOB on combustion and emissions characteristics. In addition, particulate matter (PM) emissions generated by the combustion of WPOB were analyzed. The combustion of WPOB was retarded with respect to diesel fuel, resulting in higher carbon-based emissions. The thermogravimetric analysis (TGA) results show that the temperature to reach the maximum rate of soot oxidation was lower with WPOB combustion. Because of the significant delay at the start of combustion and increase in emissions, the direct use of WPOB in the diesel engine is not recommended. It is suggested that WPOB can be used as a blend component to reduce the amount of diesel fuel used in diesel engines. Thus, further study on the effect of diesel fuel blended with WPOB on the combustion and emissions characteristics was performed. The results reveal that the maximum WPOB present in diesel fuel to avoid the increase in carbon-based emissions is 20% by volume to keep combustion and emissions characteristics similar to those of diesel fuel.

This study aims to increase machine reliability thereby preventing product defects from adhesive dispense and slider attachment by a fault detection and diagnostic technique. The experiment was set up to investigate the vibration signal and motor current. Six fault conditions of a linear bearing were set up. The approaches, including spectrum analysis, crest factor, and analysis of variance, are used for data analysis. It was found that the spectrum analysis was suitable for classifying the frequency domains and the statistics tool was successful in measuring the current. Fault detection and diagnosis results can forecast the status of the linear bearings.

Overhung rotors are important for use in industrial turbo-machines. The effects of a lateral force can increase as a result of the rotor weight, misalignment, or the operating speed of the suspension system for which the rotor is carrying a transmission connection. In this paper, the reduction of vibration in supported lateral directions by varying control is discussed in a radial active magnetic bearing system (AMBS). An experimental test was conducted on the orbital response of an overhung rotor supported by an AMBS, to provide an alternative for improving precision. To simplify the system design, decoupling was achieved using a PID controller and harmonic disturbance compensator (HDC), which improved the rotating performance of an overhung active magnetic bearing (AMB) rotor system, using a frequency response function (FRF) approach and a description of the overhung rotor during normal operational conditions at unique frequencies. The experimental results show that the precision rotation, due to harmonic excitation of the shaft orbit, can be removed in real time using compensation signals using trigonometry. The compensation criteria for the changed run-up and coast-down consistently helped to maintain the rotational center in a central position. A reduction of up to 55% in vibration amplitude on average was achieved under appropriate conditions, and the significance of the overhung rotor symptoms faults were investigated.