Dislocations are responsible for most aspects of plastic deformation in metals. In this work, the dislocation density, ρ, in brass was estimated after different deformation processes via line broadening of X-ray diffractograms using the Convolutional Multiple Whole Profile Program (CMWP) and by Transmission Electron Microscopy (TEM). In addition, we attempted to evaluate, on a global basis, the influence of crystallographic texture in ρ analysis, making sure that the results obtained by XRD could be trusted even in samples with moderate levels of texture. For this, we compared the ρ values for α brass samples (66% Cu and 34% Zn) with different levels of texture, one deformed by cold rolling and the other by equal channel angular extrusion (ECAE).The results suggest that using CMWP program it was possible to satisfactorily estimate the dislocation density in α brass. It also the was shown that the results by XRD and by TEM were self-consistent in two samples texturized to different degrees.
Analysis of dislocation density in metallic materials has been pursued with great interest for many years because dislocations are closely associated with plastic deformation and thus exert a deep effect on the mechanical properties of any material. Crystallographic texture has also a decisive influence in some properties. In this work, the dislocation density was estimated from the line broadening of X-ray diffractograms using the Convolutional Multiple Whole Profile Program (CMWP) and crystallographic texture analyses were performed using inverse pole figures (IPF). The material used in this research was pure copper deformed by cold rolling and Equal Channel Angular Pressing (ECAP). The dislocation density values obtained by Transmission Electron Microscopy (TEM) and X-ray Diffraction (XRD) were compared and discussed. While, in the case of cold rolling, the crystallographic texture of the material was enhanced with increasing deformation, it was reduced with increasing deformation in the case of ECAP processing.
29 March 2025 in The International Journal of Advanced Manufacturing Technology
No setor automotivo as ligas de alumínio têm se destacado por sua atraente combinação entre resistência/peso, entre outras características. As ligas da série 5XXX tem seu ganho de resistência mecânica através de processos de deformação a frio, e as propriedades mecânicas das ligas de alumínio estão diretamente relacionadas à sua composição e ao processo de fabricação utilizado em sua manufatura. Um dos requisitos para otimizar as operações de conformação mecânica é o controle da microestrutura e textura. Neste trabalho, as ligas AA 5052 e AA 5050C, produzidas por Fundição Direta (Direct Chill – DC), e Fundição Contínua de Chapas (Twin Roll Caster – TRC), respectivamente, passaram por caracterização mecânica via ensaio de tração (com corpos de provas extraídos a 0, 45 e 90° da direção de laminação) e caracterização estrutural e textura ao longo da espessura de chapas. Foram detectadas inclusões de alumina (Al2O3) e precipitados intermetálicos de Al3Fe juntos à matriz metálica e ambas as ligas apresentam as componentes cobre (112)[], latão (“Brass”) {110}, cubo (001)[] e Goss {110}, ao longo da espessura. A liga AA 5052 apresentou valores de coeficiente de anisotropia planar e normal superiores aos da liga AA 5050C, como também as propriedades mecânicas medidas em tração uniaxial.
Grain boundaries are fundamental in the mechanical behavior of ultrafine grain materials, especially coincidence site lattice grain boundaries (CSL-GB). This research aims to identify the influence of CSL-GB on the hardness and electrical conductivity of a CuCrZr alloy subjected to rotary swaging after having undergone severe plastic deformation via equal channel angular pressing and aging. Vickers hardness was evaluated, and electrical conductivity was measured using the 4-point technique. The average grain size and CSL-GB distribution were identified using backscattered electron diffraction. Dislocation density was measured via X-ray diffraction. At the end of the swaging processing of CuCrZr alloy with preexistent ultrafine grains, the dislocation density ceases to be the significant influencer parameter on the modification of properties, and the grain boundaries pass to be more impacting. The reduction of CSL-GB and the concomitant increase in high-angle grain boundaries can decrease hardness and electrical conductivity.
1 January 2018 in Tecnologia em Metalurgia, Materiais e Mineração