No setor automotivo as ligas de alumínio têm se destacado por sua atraente combinação entre resistência/peso, entre outras características. As ligas da série 5XXX tem seu ganho de resistência mecânica através de processos de deformação a frio, e as propriedades mecânicas das ligas de alumínio estão diretamente relacionadas à sua composição e ao processo de fabricação utilizado em sua manufatura. Um dos requisitos para otimizar as operações de conformação mecânica é o controle da microestrutura e textura. Neste trabalho, as ligas AA 5052 e AA 5050C, produzidas por Fundição Direta (Direct Chill – DC), e Fundição Contínua de Chapas (Twin Roll Caster – TRC), respectivamente, passaram por caracterização mecânica via ensaio de tração (com corpos de provas extraídos a 0, 45 e 90° da direção de laminação) e caracterização estrutural e textura ao longo da espessura de chapas. Foram detectadas inclusões de alumina (Al2O3) e precipitados intermetálicos de Al3Fe juntos à matriz metálica e ambas as ligas apresentam as componentes cobre (112)[], latão (“Brass”) {110}, cubo (001)[] e Goss {110}, ao longo da espessura. A liga AA 5052 apresentou valores de coeficiente de anisotropia planar e normal superiores aos da liga AA 5050C, como também as propriedades mecânicas medidas em tração uniaxial.
This study presents a combined experimental–numerical methodology to calibrate the mechanical behavior of an advanced high-strength steel (AHSS) with transformation-induced plasticity (TRIP) effects, incorporating both initial plastic anisotropy and ductile damage. The investigated TRIP 780 grade, widely used in the automotive industry for its exceptional strength–ductility balance, exhibits a complex deformation response that demands accurate constitutive modeling for reliable sheet metal forming simulations. The methodology minimizes the number of required specimen geometries without compromising accuracy. Three flat-sheet specimens were employed: standard uniaxial tension (UT) and two double-notched designs reproducing intermediate (ID) and plane strain (PS) modes. Experiments combined digital image correlation with finite element analysis. Hill’s 48 quadratic yield criterion captured the initial anisotropy of the TRIP 780 sheet, while the parameters of a phenomenological ductile damage model were calibrated from the experimental data. The TRIP effect under UT was quantified by X-ray diffraction, showing a decrease in retained austenite from 9.9% (as-received) to 3.2% at 21% equivalent plastic strain. Fractography revealed damage initiation dominated by void nucleation at phase boundaries. The proposed approach yielded stress–strain predictions with R2 values exceeding 0.99. This simplified approach offers a cost-effective and experimentally feasible framework for constitutive modeling of AHSS grades, enabling practical applications in advanced sheet forming simulations.
Samples of the Al 7075 naturally and artificially aged were processed by conventional and asymmetrical rolling with 5% of thickness reduction. The rolling processes were evaluated under room temperature and under warm condition (130°C). Mechanical properties were evaluated by uniaxial tensile and Vickers microhardness tests. Microstructure evolutions were followed by optical microscopy analysis. Naturally aged samples showed better yield strengthening under warm processing. Greater ultimate stress and ductility under room temperature processing was also noticed in naturally aged specimens. Artificially aged samples showed better mechanical properties under room temperature, softening under warm processing due to grain recovery process. Microhardness tests showed expected results for both rolling types, especially on asymmetrical rolling with the higher predictions were observed. Micrographs have shown no expressive grain changes or refinement although its flattening was observed. Precipitates were analyzed by EDS/SEM revealing the presence of MgZn2 and CuMgAl along the matrix that provides plastic strengthening.
5 August 2026 in The International Journal of Advanced Manufacturing Technology
Tantalum and its alloys present several challenges during welding. Among the available joining techniques, laser beam welding offers significant advantages over conventional arc and resistance welding processes. The weldability of Ta-2.5 W sheet with a thickness of 0.8 mm was investigated through bead-on-plate laser beam welding (BOP-LBW) by evaluating the influence of welding parameters: beam power (300 to 600 W), welding speed (0.5 to 3.0 mm/min), and shielding gas flow (0–10 L/min). For this purpose, 14 BOP-LBW welds (using a 2 kW multi-mode Yb: fiber laser) were performed and evaluated through visual inspection, cross-sectional weld bead analysis, Vickers hardness, X-ray Diffraction, three-point bend, and tensile (with 2 sample geometries: with and without notch) tests. The importance of shielding gas was evident, as its absence led to the incorporation of atmospheric oxygen into the molten pool, resulting in the formation of Ta₂O₅ particles and cracks in the weld bead. Three parameter sets (P500S1.25F10, P400S0.5, and P600S3.0) presented full penetration and defect-free cross sections and exhibited weld bead hardness values close to those of the base metal (BM). P500S1.25F10, P400S0.5, and P600S3.0 samples exhibited ductile behavior in three-point bend tests, with no fractures observed in the weld bead. The tensile results revealed a clear reduction in mechanical performance after BOP-LBW compared to BM, with a decrease of up to 12% in ultimate tensile strength (UTS) and 21% in elongation at fracture (EF). Nevertheless, notched specimens subjected to tensile testing still exhibited ductile behavior.