Benjamin Dawson-Andoh

Prof. Benjamin Dawson-Andoh


Research Focus & Metrics

Academic Career Length

25Years (2002-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2008 in Journal of Near Infrared Spectroscopy
Verified
Journal Article
Closed access
OAOluwatosin Emmanuel Adedipe
Oluwatosin Emmanuel Adedipe
BDBenjamin Dawson-Andoh
Benjamin Dawson-Andoh
JSJeffrey Slahor
Jeffrey Slahor
LOLarry Osborn
Larry Osborn
In this study, a method suitable for online rapid classification and separation of red oak and white oak wood species has been developed with the use of near infrared (NIR) spectroscopy and soft independent modeling of class analogies (SIMCA). The spectra of 150 wood specimens of each species were collected over wavelength window of 800–2500 nm. The raw spectra and spectra pre-treated by first derivative and standard normal variate (SNV) transformation were used to develop calibration models using the wavelength ranges 800–2500 nm, 1100–2200 nm and 1400–1900 nm by the SIMCA method. Principal component analysis (PCA) models were made for each class from the calibration set consisting of 100 specimens of red oak and white oak, respectively, and specimens not present in the calibration set (Testing set) consisting of 100 specimens were tested for classification according to the SIMCA method at the 5% and 25% significance level. Type I error (rejection of true member) associated with the models developed ranged from 2% to 20% and from 16% to 66%, respectively, for 5% and 25% significance level, while type II error (acceptance of a false member) was 0% for all models developed. There was no significant improvement in models developed with spectra pre-treated with first derivative or standard normal variate transformation over models developed with raw spectra. The full NIR spectral region of 800–2500 nm provided the most useful information for distinguishing between the two species. The results of this study showed that NIR spectroscopy coupled with the SIMCA method of multivariate data analysis could be used to reliably separate and sort wood of red oak and white oak.

10 March 2021 in Sustainable Chemistry
Verified
Journal Article
Open access
PDF file
GLGideon Lawer-Yolar
Gideon Lawer-Yolar
BDBenjamin Dawson-Andoh
Benjamin Dawson-Andoh
EAEmmanuel Atta-Obeng
Emmanuel Atta-Obeng
This study compared the yield of biodiesel produced from tall oil fatty acids (TOFA) via (i) homogeneous catalyst (sulfuric acid) and (ii) a heterogeneous catalyst (Amberlyst® BD20, together with Ambersep BD 19 (Midcontinental Chemical Co., Olathe, KS, USA)® using a batch reactor. The effect of operation conditions including temperature, catalyst concentration, methanol: oil ratio and reaction time on esterification yield were investigated. Gas chromatographic data showed that the major fatty acids present in the TOFA are oleic acid (C18:1n9) and linoleic acid (C18:2n6). Homogenous catalysis yielded 96.76% biodiesel compared to 90.24% for heterogeneous catalysis. Optimized conditions for homogenous catalysis were at a catalyst concentration of 0.5 w/w%, 15:1 methanol: oil mass ratio at 55 °C for 60 min. FTIR results also showed that the homogeneous catalyst yielded a more complete reaction toward biodiesel production in a shorter time (60 min) compared to the heterogeneous catalyst (4.7 h). For heterogeneous catalysis, the highest yield and the lowest acid value were achieved after a second recycling because the reactants were not fully in contact with the catalyst during the first recycling. The catalyst did not show a reduction in catalytic activity even after the fourth recycling. However, the acid value was higher than that for ASTM standards for biodiesel.

1 December 2004 in Journal of Vinyl and Additive Technology
Verified
Journal Article
Closed access
PDF file
BDBenjamin Dawson-Andoh
Benjamin Dawson-Andoh
LMLaurent M. Matuana
Laurent M. Matuana
JHJoel Harrison
Joel Harrison

1 December 2019 in Biotechnology Reports
Verified
Journal Article
Open access
GLGideon Lawer-Yolar
Gideon Lawer-Yolar
BDBenjamin Dawson-Andoh
Benjamin Dawson-Andoh
EAEmmanuel Atta-Obeng
Emmanuel Atta-Obeng
We report for the first time the evaluation of oils from the tropical forest tree, Allanblackia, shea butter and palm kernel oil as a potential phase change material for thermal energy storage based upon its thermo-physical and chemical properties. Differential Scanning Calorimetry showed that all the oils were polymorphic and hence exhibited multiple melting/freezing profile over a wide range. For both melting and freezing cycles, Allanblackia oil showed high latent heat of energy (80.53 J/g) with the highest melting point profile (34.74 °C) of all the oils. Thermo-gravimetric analysis showed that all the oil samples were thermally stable and did not degrade within the temperature of interest even though Allanblackia oil showed an increase in weight around 37 °C indicating oxidative instability. Chemical stability was confirmed by FTIR spectra. Of all the oils studied, Allanblackia exhibited a potential for use as a PCM for thermal energy storage if purified to improve oxidative stability.

27 March 2018 in Waste and Biomass Valorization
Verified
Journal Article
Closed access
PDF file
EAEmmanuel Atta-Obeng
Emmanuel Atta-Obeng
BDBenjamin Dawson-Andoh
Benjamin Dawson-Andoh
EFEugene Felton
Eugene Felton
GDGreg Dahle
Greg Dahle

1 January 2008 in Journal of Near Infrared Spectroscopy
Verified
Journal Article
Closed access
OAOluwatosin Emmanuel Adedipe
Oluwatosin Emmanuel Adedipe
BDBenjamin Dawson-Andoh
Benjamin Dawson-Andoh
This study investigated the feasibility of using near infrared (NIR) spectroscopy and multivariate calibration to predict bulk density and stiffness of 3.2 mm thick yellow poplar veneer strips. Full-range (800–2500 nm) raw NIR spectra and spectra pre-treated using the first derivative method, along with spectra from three other different wavelength windows of 1200–2400 nm, 1800–2400 nm and 1400–2000 nm were regressed against the bulk density (kg m−3) values and the dynamic modulus of elasticity (stiffness; GPa) of the veneers using the projection to latent structures (PLS) method to develop calibration models. All predictive models developed performed well in the prediction of bulk density and stiffness of new test samples that were not included in the calibration models. R2 values ranged from 0.67-0.78 and 0.56-0.72, respectively, for bulk density and stiffness. There was significant improvement in models developed with first derivative spectra over models developed with raw spectra. The models developed using the first derivative used fewer latent variables to achieve predictive models with higher R2 values, lower root mean square errors of prediction (RMSEP) and standard errors of prediction (SEP). Models developed using the full NIR spectral range (800–2500 nm) and the NIR spectral region of 1200–2400 nm performed better than models developed using the restricted NIR wavelength regions of 1800–2400 nm and 1400–2000 nm. However, there was no clear distinction between models developed using the full NIR spectral range and the NIR spectral region of 1200–2400 nm. Overall, models developed with the first derivative pre-processed spectra using the whole NIR spectrum performed best in predictability. The results of this study show the potential of using multivariate data analysis coupled with NIR spectroscopy for on-line sorting and assessment of veneer stiffness prior to the lay-up process in the manufacturing of veneer-based engineered wood products such as plywood, Parallam and laminated veneer lumber.