The fast and accurate modeling topologies are very much essential for power train electrification. The importance of thermal effect is very important in any electrochemical systems and must be considered in battery models because temperature factor has highest importance in transport phenomena and chemical kinetics. The dynamic performance of the lithium ion battery is discussed here and a suitable electrical equivalent circuit is developed to study its response for sudden changes in the output. An effective lithium cell simulation model with thermal dependence is presented in this paper. One series resistor, one voltage source and a single RC block form the proposed equivalent circuit model. The 1 RC and 2 RC Lithium ion battery models are commonly used in the literature are studied and compared. The simulation of Lithium-ion battery 1RC and 2 RC Models are performed by using Matlab/Simulink Software. The simulation results in his paper shows that Lithium-ion battery 1 RC model has more maximum output error of 0.42% than 2 RC Lithium-ion battery model in constant current condition and the maximum output error of 1 RC Lithium-ion battery model is 0.18% more than 2 RC Lithium-ion battery model in UDDS Cycle condition. The simulation results also show that in both simple and complex discharging modes, the error in output is much improved in 2 RC lithium ion battery model when compared to 1 RC Lithium-ion battery model. Thus the paper shows for general applications like in portable electronic design like laptops, Lithium-ion battery 1 RC model is the preferred choice and for automotive and space design applications, Lithium-ion 2 RC model is the preferred choice. In this paper, these simulation results for 1 RC and 2 RC Lithium-ion battery models will be very much useful in the application of practical Lithium-ion battery management systems for electric vehicle applications.

The recognition of handwritten digits holds a significant place in the field of information processing. Recognizing such characters accurately from images is a complex task because of the vast differences in people's writing styles. Furthermore, the presence of various image artifacts such as blurring, intensity variations, and noise adds to the complexity of this process. The existing algorithm, convolution neural network (CNN) is one of the prominent algorithms in deep learning to handle the above problems. But there is a difficulty in handling input data that differs significantly from the training data, leading to decreased accuracy and performance. In this work, a method is proposed to overcome the aforementioned limitations by incorporating a quantum convolutional neural network algorithm (QCNN). QCNN is capable of performing more complex operations than classical CNNs. It can achieve higher levels of accuracy than classical CNNs, especially when working with noisy or incomplete data. It has the potential to scale more efficiently and effectively than classical CNNs, making them better suited for large-scale applications. The effectiveness of the proposed model is demonstrated on the modified national institute of standards and technology (MNIST) dataset and achieved an average accuracy of 91.08%.

It is widely accepted that electrochemical batteries ensure superior energy storage and reliability of power supply. This paper proposes to discuss the dynamic performance of the Lead Acid Storage battery and to develop an Electrical Equivalent circuit and study its response to sudden changes in the output. A detailed explanation of the discharging process for lead-acid storage batteries and the factors affecting the rate of chemical reactions is provided. The objective of the study is to find the reduction in terminal voltage due to the change in reaction rate and to evolve a simple dynamic model for discharge of the battery.

GSM/GPRS and PLC communication are used for Automatic Meter Reading (AMR) applications. These AMR systems have made substantial progress over the recent years in terms of functionality, scalability, performance and openness such that they can perform remote metering applications for very demanding and complex systems. By using BPSK (Binary Phase Shift Keying) modulation with Power Line Carrier Communication, Smart Metering can be done in Rural Smart Micro-grids. The design and Simulation of BPSK Modulation and Demodulation are successfully done by using MATLAB/Simulink software. The advantages of using BPSK modulation over the QPSK modulation and the advantages of PLC Communication over the GSM Communication is identified in this paper.

Maximum power point tracking (MPPT) of a photo voltaic system with different temperature and insolation conditions used for Micro grids can be explained in this paper. The different steps of the design of this controller are presented together with its simulation and the feasibility of control methods to be adopted for the operation of a micro grid when it becomes isolated. Normally, the micro grid operates in interconnected mode with the medium voltage network; however, scheduled or forced isolation can take place. In such conditions, the micro grid must have the ability to operate stably and autonomously. An evaluation of the need of storage devices and load to take off strategies is included in this paper. Solar photovoltaic (PV) energy has witnessed double-digit growth in the past decade. The penetration of PV systems as distributed generators in low-voltage grids has also seen significant attention. In addition, the need for higher overall grid efficiency and reliability has boosted the interest in the microgrid concept. High-efficiency PV-based microgrids require maximum power point tracking (MPPT) controllers to maximize the harvested energy due to the nonlinearity in PV module characteristics. This paper proposes an approach of coordinated and integrated control of solar PV generators with the maximum power point tracking (MPPT) control and battery storage control to provide voltage and frequency (V-f) support to an islanded microgrid. The simulation studies are carried out with the IEEE 13-bus feeder test system in grid connected and islanded microgrid modes. The MPPT of a Photovoltaic System for Micro Grid operation is successfully designed and simulated by using MATLAB/Simulink Software in this paper.

The inverter with critical loads should be able to provide critical loads with a stable and seamless voltage during control mode change as well as clearing time. The indirect current control has been proposed for providing stable voltage with critical load during clearing time and seamless control mode transfer of inverters. However, the islanding detection is difficult since with the indirect current control the magnitude and frequency of voltage do not change when the islanding occurs. The conventional anti-islanding method based on the magnitude and frequency of voltage variation cannot apply to the indirect current control. This paper proposes an islanding detection method for the indirect current control. The proposed islanding detection method can detect the islanding using reactive power perturbation and observation when the frequency and magnitude of voltage don’t vary during clearing time. In order to verify the proposed anti-islanding method, the experimental results of a 600W three-phase inverter are provided.