Quantum yield values up to 16% under visible irradiation associated with high turnover frequencies (∼50 h−1) and stability (up to 273 turnovers), characterize the new photocatalytic systems for hydrogen production, based on diimine derivatives of ruthenium, cyclometallated iridium or tricarbonylrhenium as photosensitizers and cobaloxime H2-evolving catalytic centers, which are among the most efficient molecular systems reported so far and compete with some platinum-based systems.
Steady-state irradiation under visible light of a covalent Ir(III)-photosensitized polyoxotungstate is reported. In the presence of a sacrificial electron donor, photolysis leads to a very efficient photoreduction of the polyoxometalate. Successive formation of the one-electron and two-electron reduced species, which are unambiguously identified by comparison with spectroelectrochemical measurements, is observed with a significantly faster rate reaction for the formation of the one-electron reduced species. The kinetics of the photoreduction, which are correlated with the reduction potentials of the polyoxometalate (POM), can be finely tuned by the presence of an acid. Indeed light-driven formation of the two-electron reduced POM is considerably facilitated in the presence of acetic acid. The system is also able to perform photocatalytic hydrogen production under visible light without significant loss of performance over more than 1 week of continuous photolysis and displays higher photocatalytic efficiency than the related multi-component system, outlining the decisive effect of the covalent bonding between the POM and the photosensitizer. This functional and modular system constitutes a promising step for the development of charge photoaccumulation devices and subsequent photoelectrocatalysts for artificial photosynthesis.
22 August 2012 in Physical Chemistry Chemical Physics
This work reports a facile and cost-effective method for synthesizing photoactive α-Fe2O3 films as well as their performances when used as photoanodes for water oxidation. Transparent α-Fe2O3 mesoporous films were fabricated by template-directed sol–gel chemistry coupled with the dip-coating approach, followed by annealing at various temperatures from 350 °C to 750 °C in air. α-Fe2O3 films were characterized by X-ray diffraction, XPS, FE-SEM and electrochemical measurements. The photoelectrochemical performance of α-Fe2O3 photoanodes was characterized and optimized through the deposition of Co-based co-catalysts via different methods (impregnation, electro-deposition and photo-electro-deposition). Interestingly, the resulting hematite films heat-treated at relatively low temperature (500 °C), and therefore devoid of any extrinsic dopant, achieve light-driven water oxidation under near-to-neutral (pH = 8) aqueous conditions after decoration with a Co catalyst. The onset potential is 0.75 V vs. the reversible hydrogen electrode (RHE), thus corresponding to 450 mV light-induced underpotential, although modest photocurrent density values (40 μA cm−2) are obtained below 1.23 V vs. RHE. These new materials with a very large interfacial area in contact with the electrolyte and allowing for a high loading of water oxidation catalysts open new avenues for the optimization of photo-electrochemical water splitting.
The low-power sensing platform proposed by the Convergence project is foreseen as a wireless, low-power and multifunctional wearable system empowered by energy-efficient technologies. This will allow meeting the strict demands of life-style and healthcare applications in terms of autonomy for quasi-continuous collection of data for early-detection strategies. The system is compatible with different kinds of sensors, able to monitor not only health indicators of individual person (physical activity, core body temperature and biomarkers) but also the environment with chemical composition of the ambient air (NOx, COx, NHx particles) returning meaningful information on his/her exposure to dangerous (safety) or pollutant agents. In this article, we introduce the specifications and the design of the low-power sensing platform and the different sensors developed in the project, with a particular focus on pollutant sensing capabilities and specifically on NO2 sensor based on graphene and CO sensor based on polyaniline ink.
1 December 2019 in Surface and Coatings Technology