The next-generation application of pressure sensors is gradually being extended to include electronic artificial skin (e-skin), wearable devices, humanoid robotics and smart prosthetics. In these advanced applications, high sensing capability is an essential feature for high performance. Although surface patterning treatments and some special elastomeric interlayers have been applied to improve sensitivity, the process is complex and this inevitably raises the cost and is an obstacle to large-scale production. In the present study a simple printing process without complex patterning has been used for constructing the sensor, and an interlayer is employed comprising elastomeric composites filled with silver nanowires. By increasing the relative permittivity, εr, of the composite interlayer induced by compression at high nanowire concentration, it has been possible to achieve a maximum sensitivity of 5.54 kPa−1. The improvement in sensitivity did not sacrifice or undermine the other features of the sensor. Thanks to the silver nanowire electrodes, the sensor is flexible and stable after 200 cycles at a bending radius of 2 mm, and exhibits outstanding reproducibility without hysteresis under similar pressure pulses. The sensor has been readily integrated onto an adhesive bandage and has been successful in detecting human movements. In addition to measuring pressure in direct contact, non-contact pressures such as air flow can also be detected.
We demonstrate the fabrication of highly transparent conductive networks on a cellulose nanofiber paper, called cellulose nanopaper. Uniform coating of the conductive nanomaterials, such as silver nanowires (AgNWs) and carbon nanotubes, is achieved by simple filtration of their aqueous dispersions through the cellulose nanopaper, which acts as both filter and transparent flexible substrate. The as-prepared AgNW networks on the nanopaper offer sheet resistance of 12 Ω sq.−1 with optical transparency of 88%, which is up to 75 times lower than the sheet resistance on a polyethylene terephthalate film prepared by conventional coating processes. These results indicate that the ‘filtration coating’ provides uniformly connected conductive networks because of drainage in the perpendicular direction through paper-specific nanopores, whereas conventional coating processes inevitably cause self-aggregation and uneven distribution of the conductive nanomaterials because of the hard-to-control drying process, as indicated by the well-known coffee-ring effect. Furthermore, the conductive networks are embedded in the surface layer of the nanopaper, showing strong adhesion to the nanopaper substrate and providing foldability with negligible changes in electrical conductivity. This filtration process is thus expected to offer an effective coating approach for various conductive materials, and the resulting transparent conductive nanopaper is a promising material for future paper electronics.
24 September 2012 in Journal of Materials Chemistry
Large-scale silver nanowire (AgNW) mesh films have received increasing attention as new transparent conductive films used in various printed devices. However, there are two crucial issues in implementing AgNWs that need to be addressed: (1) strong adhesion between AgNW film and substrate and (2) high conductivity with short treatment time for low-cost printed technology. Here, a high-intensity pulsed light (HIPL) sintering technique, which provides extreme heating locally in the AgNW film and at the interface between the film and polymer substrate, sinters the AgNW film to produce high conductivity with strong adhesion on the substrate. Importantly, light intensity, exposure time, and AgNW amount can be adjusted simply to form films that meet specific device needs. A flexible AgNW film with sheet resistance of 19 Ω sq−1 and transmittance of 83% at 550 nm is obtained with only one-step on a polyethylene terephthalate substrate with a light intensity of 1.14 J cm−2 under an exposure time of only 50 μs. The film can endure multiple peeling tests, which will play an important role in printed electronics.
Transparent electrodes made of silver nanowires (AgNWs) exhibit higher flexibility when compared to those made of tin doped indium oxide (ITO) and are expected to be applied in plastic electronics. However, these transparent electrodes composed of AgNWs show high haze because the wires cause strong light scattering in the visible range. Reduction of the wire diameter has been proposed as a way to weaken light scattering, although there have seldom been any studies focusing on the haze because of the difficulty involved in controlling the wire diameter. In this report, we show that the haze can be easily reduced by increasing the length of AgNWs with a large diameter. Ultra-long (u-long) AgNWs with lengths in the range of 20–100 μm and a maximum length of 230 μm have been successfully synthesized by adjusting the reaction temperature and the stirring speed of a one-step polyol process. Compared to typical AgNWs (with diameter and length of 70 nm and 10 μm, respectively) and ITO, a transparent electrode consisting of u-long AgNWs 91 nm in diameter demonstrated a low haze of 3.4%-1.6% and a low sheet resistance of 24–109 Ω/sq. at a transmittance of 94%–97%. Even when fabricated at room temperature without any post-treatment, the electrodes composed of u-long AgNWs achieved a sheet resistance of 19 Ω/sq. at a transmittance of 80%, which is six orders of magnitude lower than that of typical AgNWs.