Sergey Ruchkin

Prof. Sergey Ruchkin

Junior Researcher

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 February 2021 in Coatings
Verified
Journal Article
Open access
PDF file
Dmitrii SidelevDmitrii Sidelev
Dmitrii Sidelev
MSMaxim Syrtanov
Maxim Syrtanov
Sergey RuchkinSergey Ruchkin
Sergey Ruchkin
AАAlexey Алексей
Alexey Алексей
Egor KashkarovEgor Kashkarov
Egor Kashkarov
Metallic Cr and multilayer CrN/Cr coatings with a thickness of 2.5 µm were deposited onto E110 alloy by magnetron sputtering. Oxidation tests in air were performed at 1100 °C for 10–40 min. The gravimetric measurements showed better protective properties of multilayer CrN/Cr coatings in comparison with metallic Cr coating. Multilayer coating prevented fast Cr–Zr inter-diffusion by the formation of a ZrN layer beneath the coating. The appearance of ZrN is caused by interaction with nitrogen formed from the decomposition of CrN to Cr2N phases. Optical microscopy revealed a residual Cr layer for the multilayer CrN (0.25 µm)/Cr (0.25 µm) coating for all the oxidation periods. Additional in situ X-ray diffraction (XRD) studies of coated alloy during linear heating up to 1400 °C showed that the formation of the Cr2Zr phase in the case of multilayer coatings occurred at a higher (~150 °C) temperature compared to metallic Cr. Multilayer coatings can decrease the nitrogen effect for Zr alloy oxidation. Uniform and thinner oxide layers of Zr alloy were observed when the multilayer coatings were applied. The highest oxidation resistance belonged to the CrN/Cr coating with a multilayer step of 0.25 µm.

27 September 2022 in Coatings
Verified
Journal Article
Open access
PDF file
Dmitrii SidelevDmitrii Sidelev
Dmitrii Sidelev
Sergey RuchkinSergey Ruchkin
Sergey Ruchkin
ISIvan Andreevich Shelepov
Ivan Andreevich Shelepov
NSNikolay Sergeevich Saburov
Nikolay Sergeevich Saburov
AMAndrey Gennadievich Malgin
Andrey Gennadievich Malgin
AMAndrey Andreevich Mokrushin
Andrey Andreevich Mokrushin
This article described the protective properties of Cr coatings with a barrier layer composed of ZrO2/Cr multilayers deposited onto E110 zirconium alloy. The coatings with a ZrO2/Cr multilayer thickness of 100, 250, and 750 nm and single-layer (1.5 µm) ZrO2 barrier were obtained by multi-cathode magnetron sputtering in Ar + O2 atmosphere. Then, cracking resistance and oxidation behavior were studied under conditions of thermal cycling (1000 °C) in air and high-temperature oxidation at 1200–1400 °C in a water steam. The role of the ZrO2/Cr multilayers and multilayer thickness on cracking resistance of the experimental coatings and oxidation resistance of the coated E110 alloy was discussed. It was shown that the coatings with more quantity of the ZrO2/Cr multilayers have higher cracking resistance, but such types of samples have a large amount of coating spallation under thermal cycling. The high-temperature steam oxidation (1200–1400 °C) demonstrated that interfaces of the ZrO2/Cr multilayers can act as a source of cavities formed by the Kirkendall mechanism that results in accelerating Cr–Zr interdiffusion for Cr-coated E110 alloy.

15 May 2021 in Coatings
Verified
Journal Article
Open access
PDF file
Dmitrii SidelevDmitrii Sidelev
Dmitrii Sidelev
Sergey RuchkinSergey Ruchkin
Sergey Ruchkin
Egor KashkarovEgor Kashkarov
Egor Kashkarov
The resistance upset welds (RUW) made from E110 alloy without and with Cr coatings were oxidized in air atmosphere at 1100 °C for 2, 10 and 30 min. The cross-section microstructure, elemental composition and hardness were studied before and after oxidation using optical and scanning electron microscopy, and indentations in welding region. The RUW welding does not noticeably change oxidation kinetics of E110 alloy. The most crucial effect has surface non-regularities formed after welding, which prevent uniform coating deposition on full surface of welded cladding tube and end plug. Cr coating deposition can strongly reduce oxidation of welded E110 alloy, while additional post-processing treatment should be applied to improve surface morphology after RUW welding. Several suggestions favorable to development of ATF Zr-based claddings using Cr coating deposition on welded nuclear rods were discussed.