Near-field resonant-based wireless power transfer (WPT) technology has a significant impact in many applications ranging from charging of biomedical implants to electric vehicles (EVs). The design of robust WPT systems is challenging due to its position-dependent power transfer efficiency (PTE). In this paper, a new approach is presented to address WPT's strong sensitivity to the coupling factor variation between the transmit and receive coils. The introduced technique relies on harnessing the unique properties of a specific class of nonlinear resonant circuits to design position-insensitive WPT systems that maintain a high PTE over large transmission distances and misalignments without tuning the source's operating frequency or employing tunable matching networks, as well as any active feedback/control circuitry. A nonlinear-resonant-based WPT circuit capable of transmitting 60 W at 2.25 MHz is designed and fabricated. The circuit maintains a high PTE of 86% over a transmission distance variation of 20 cm. Furthermore, transmit power and PTE are maintained over a large lateral misalignment up to ± 50% of the coil diameter and angular misalignment up to ± 75°. The new design approach enhances the performance of WPT systems by significantly extending the range of coupling factors over which both load power and high PTE are maintained.
24 January 2023 in IEEE Journal of Solid-State Circuits
In this work, we present an open-source fully-synthesizable fractional-N all-digital phase-locked loop (ADPLL) designed for a Bluetooth low-energy (BLE) transmitter (TX) along with a semi-analytical model of the PLL fractional spur’s impact on the BLE output spectrum. Based on the model and the BLE specification for spur emission, a requirement for the PLL fractional spurs is derived. To meet the derived spectral mask by reducing the fractional spurs, a novel synthesizable two-step time to digital converter (TSTDC) that employs embedded TDC (EMBTDC) as coarse and Vernier delay-line TDC (DLTDC) as fine TDC is proposed. We also present a digital calibration scheme to compensate for the nonlinearity induced by the place-and-route (P&R) tool. The PLL is fabricated in 12-nm FinFET and demonstrated in a BLE-TX. The measured BLE transmissions satisfy the standard requirements thanks to the reduced fractional spurs. In a standalone PLL mode, the proposed TSTDC and calibration scheme reduced the fractional spurs by 14.3 dB compared to only using an EMBTDC in near-integer $N$ operation. The PLL supports a frequency range of 1.8–2.7 GHz and consumes 3.91 mW at 2.4006 GHz achieving figure of merit (FoM) of $-$ 220.7 dB in fractional-N mode with a 40 MHz reference, occupying an area of 0.063 mm $^{2}$ . A highly automated design flow is used for the PLL to lower the barrier for new developers and reduce the porting cost.
Energy-efficient wireless connectivity plays an important role in scaling both battery-less and battery-powered Internet-of-Things (IoT) devices. The power consumption in these devices is dominated by the wireless transceivers which limit the battery’s lifetime. Different strategies have been proposed to tackle these issues both in physical and network layers. The ultimate goal is to lower the power consumption without sacrificing other important metrics like latency, transmission range and robust operation under the presence of interference. Joint efforts in designing energy-efficient wireless protocols and low-power radio architectures result in achieving sub-100 μW operation. One technique to lower power is back-channel (BC) communication which allows ultra-low power (ULP) receivers to communicate efficiently with commonly used wireless standards like Bluetooth Low-Energy (BLE) while utilizing the already-deployed infrastructure. In this paper, we present a review of BLE back-channel communication and its forms. Additionally, a comprehensive survey of ULP radio design trends and techniques in both Bluetooth transmitters and receivers is presented.
This paper presents the design of a wide dynamic range rectifier array using a novel adaptive power distribution method. In such a rectifier array, the RF input power is distributed among multiple rectifier devices adaptively, according to their impedances as a function of input power level. Such a rectifier array can achieve high rectification efficiency and low reflection coefficient over a wide range of power levels. The method is experimentally verified with a 900 MHz two-device rectifier array, and demonstrated an efficiency higher than 50% over 17 dB dynamic range (10 dB wider than a conventional rectifier design using the same devices) with a peak efficiency of 66%.
In this work, we present an open-source fully-synthesizable fractional-N ADPLL designed for a Bluetooth Low-Energy (BLE) transmitter (TX). A highly automated design flow is used to lower the barrier for new developers and to reduce porting cost. In the PLL, a novel two-step TDC (TSTDC) is proposed, which is amenable to P&R, and uses an embedded TDC (EMBTDC) and vernier delay-line TDC (DLTDC) as coarse and fine TDCs, respectively. This combination reduces the required DLTDC input time range by 5x and is used to measure and compensate the P&R induced non-linearity of the EMBTDC. The PLL is fabricated in 12-nm FinFET and demonstrated in a BLE-TX. BLE transmissions satisfy the standard requirements thanks to the reduced fractional spurs by abovementioned techniques. In a standalone PLL mode, the TSTDC reduced fractional spurs by 6.8 dB compared to an EMBTDC alone, and the proposed LUT-based calibration further reduced spurs by 7.5 dB in near-integer operation. The PLL supports frequency range of 1.8-2.7GHz and consumes 3.91mW at 2.4006 GHz, with a 40MHz reference, occupying area of 0.063mm 2 .