In this paper, we present an all-digital ring oscillator (RO)-based Bluetooth low-energy (BLE) transmitter (TX) for ultra-low-power radios in short range Internet-of-Things (IoT) applications. The power consumption of state-of-the-art BLE TXs has been limited by the relatively power-hungry local oscillator (LO) due to the use of LC oscillators for superior phase noise (PN) performance. This paper addresses this issue by analyzing the PN limit of a BLE TX and proposes an RO-based solution for power and cost savings. The proposed transmitter features: 1) a wideband all-digital phase-locked loop (ADPLL) featuring an fRF / 4 RO, with an embedded 5-bit TDC; 2) a 4x frequency edge combiner to generate the 2.4-GHz signal; and 3) a switch-capacitor digital PA optimized for high efficiency at low transmit power levels. These not only help reduce the power consumption and improve PN performance but also enhance the TX efficiency for short range applications. The TX is prototyped in 40-nm CMOS, occupies an active area of 0.0166 mm², and consumes 486 μW in its low-power mode, while configured as a non-connectable advertiser. The TX has been validated by wirelessly communicating beacon messages to a mobile phone.

A 40-nm CMOS IEEE 802.11ba low-power wake-up receiver (LP-WUR) is presented. It receives 802.11ba messages generated by an 802.11 orthogonal frequency-division multiplexing (OFDM) transmitter operating at 5.8 GHz. The power consumption of the RF front-end is minimized by removing active RF gain stages and using a third harmonic passive mixer with a ring-based local oscillator (LO) operating at one-third of the RF frequency. The noise figure is 14 dB, taking advantage of a 1:3 transformer that provides passive voltage gain in front of the high switch loss mixer-first RF front-end, and matching across 5.5-5.8 GHz with <-12 dB S₁₁. The receiver achieves a sensitivity of -83-dBm and -20-dB adjacent channel signal-to-interference ratio (SIR) while consuming 220 μW at a bit error rate (BER) of 10⁺³ and data rate of 62.5 kb/s, which shows the best sensitivity-power tradeoff among >3-GHz receivers.

Improving system lifetime and robustness is a key to advancing self-powered platforms for real world applications. A complete self-powered, battery-less, wearable platform requires a microwatt-power system-on-chip (SoC), operating reliably within this budget, capable of surviving long periods without charging, and recovering from power loss to its previous state. To meet these requirements, we designed a wireless sensing heterogeneous system-in-package (SiP) containing an ultra-low power (ULP) SoC, a non-volatile boot memory (NVM), and a 2.4 GHz frequency shift key (FSK) radio, all integrated with custom ULP interfaces. The SoC includes a fully integrated energy harvesting platform power manager (EH-PPM) to power the SiP and other commercial sensors. The EH-PPM is designed for small loads and powers the SoC and peripherals while drawing very low operating current. The SoC also includes a digital system data-flow for sensing applications, an analog front end for ECG signal acquisition, and a cold-boot management system (CBMS) for boot and recovery from the NVM. The CBMS enables integration of the SoC with the ULP NVM to create a wearable formfactor, self-powered system capable of recovery from power loss. The SoC also includes a radio interface tightly integrated with a compression accelerator to efficiently communicate with the FSK transmitter and reduce the FSK's transmission time. This tight integration between accelerators on the SoC and peripherals is another feature that reduces the system's power consumption by reducing the code size and number of memory accesses required to perform an operation. The SoC consumes 507 nW average power while running free-fall detection, 519 nW average power while measuring ambient temperature, and 1.02 μW during continuous ECG monitoring and post-processing.

This paper presents a power efficient analog front-end (AFE) for electrocardiogram (ECG) signal monitoring and arrhythmia diagnosis. The AFE uses low-noise and low-power circuit design methodologies and aggressive voltage scaling to satisfy both the low power consumption and low input-referred noise requirements of ECG signal acquisition systems. The AFE was realized with a three-stage fully differential AC-coupled amplifier, and it provides bio-signal acquisition with programmable gain and bandwidth. The AFE was implemented in a 130 nm CMOS process, and it has a measured tunable mid-band gain from 31 to 52 dB with tunable low-pass and high-pass corner frequencies. Under only 0.5 V supply voltage, it consumes 68 nW of power with an input-referred noise of 2.8 µVrms and a power efficiency factor (PEF) of 3.9, which makes it very suitable for energy-harvesting applications. The low-noise 68nW AFE was also integrated on a self-powered physiological monitoring System on Chip (SoC) that is used to capture ECG bio-signals. Heart rate extraction (R-R) detection algorithms were implemented and utilized to analyze the ECG data received by the AFE, showing the feasibility of <100 nW AFE for continuous ECG monitoring applications.

Wireless communication has been a limiting factor for achieving millimeter-sized wireless sensor nodes because of the high power consumption, large antenna size and off-chip components typically required. Several mm-scale radios have been proposed [1-3]; however, all use proprietary communication protocols, which afford their designers more flexibility to address the above challenges. For interoperability and ubiquitous adoption, it is important that mm-scale radios use standard protocols, such as Bluetooth Low Energy (BLE). However, implementing a BLE-compliant radio in a mm-scale form factor poses significant additional challenges. These include the requirements for center frequency deviation (<;150kHz), FSK modulation accuracy and frequency drift during the packet (<;50kHz), which drive up the power consumption of typical PLL+VCO+PA BLE transmitters to >3mW [4-5]. A 0.5mW BLE transmitter was achieved by relaxing these requirements, but suffered from high phase noise due to its low-power ring oscillator [6].