Cationic polyacrylamide copolymers (PAMs) are used for sludge dewatering in municipal waste water treatment and might enter the environment by spreading of the sludge on agricultural land. Concern has been expressed since little is known about the degradation of PAMs in soils. To obtain detailed information on the polymer’s fate in the soil compartment, the degradation of 14C-radiolabelled PAM in an outdoor lysimeter was studied. No plant uptake and leaching of radioactivity was observed. There was practically no vertical movement of polymer and no transformation products found at the end of the study. For the top 10 cm soil layer, a mass balance was established throughout the study. About 10% of applied radioactivity was not extractable from soil even with a matrix destructive method, and this was concluded to be bound residue. Characterization of extractable radioactivity by means of GPC-analysis showed a significant decrease of the molecular weight of the PAM with time. The decrease in molecular weight indicates a breakdown of the polymer backbone (the C–C-chain), and is assumed to be primary degradation. The total radioactivity content in the 10 cm top soil layer was quantified every 6 months over a period of 3 years. The results show a significant decrease of the total radioactivity over time and this is defined as ultimate degradation following the definition of OECD and EPA. Based on the data, a half-life time of 2.0 × 103 days and a rate constant of 0.00035/day were calculated. With a χ2 of 12.0 the results of the calculation are thus valid and reliable. The rate constant indicates a mineralization of 22.5% within a period of 2 years based on the total recovered radioactivity. This half-life time is solely based on mineralization and does not take into account the degradation of the polymer backbone, hydrolysis of the side chains, incorporation into the soil matrix, and thus is a conservative approach. 14C-PAM degrades very slowly in soil after land-spreading as a component of sewage sludge. Even in a very conservative evaluation which only considered the loss of radioactivity, a half-life time of 5.4 years was determined.

Solid surfaces are modified using photo-crosslinkable copolymers based on oligo(ethylene glycol) methacrylate (OEGMA) bearing 2-(4-benzoylphenoxy)ethyl methacrylate (BPEM) as a photosensitive crosslinking unit. Thin films of about 100 nm are formed by spin-coating these a priori highly biocompatible copolymers onto silicon substrates. Subsequent UV-irradiation assures immobilization and crosslinking of the hydrogel films. Their stability is controlled by the number of crosslinker units per chain and the molar mass of the copolymers. The swelling of the hydrogel layers, as investigated by ellipsometry, can be tuned by the crosslinker content in the copolymer. If films are built from the ternary copolymers of OEGMA, BPEM and 2-(2-methoxyethoxy) ethyl methacrylate (MEO₂MA), the hydrogel films exhibit a swelling/deswelling transition of the lower critical solution temperature (LCST) type. The observed thermally induced hydrogel collapse is fully reversible and the onset temperature of the transition can be tuned at will by the copolymer composition. Different from analogously prepared thermo-responsive hydrogel films of photocrosslinked poly(N-isopropylacrylamide), the swelling–deswelling transition occurs more gradually, but shows no hysteresis.

Electronics (particularly power electronics) are the core element in many energy-related applications. Due to the increasing power density of electronic parts, the demands on thermal management solutions have risen considerably. As a novel passive and highly efficient cooling technology, pulsating heat pipes (PHPs) can transfer heat away from critical hotspots. In this work, we present two types of small and compact PHPs with footprints of 50 × 100 mm², thicknesses of 2 and 2.5 mm and with high fluid channel density, optimized for cooling electronic parts with high power densities. The characterization of these PHPs was carried out with a strong relation to practical applications, revealing excellent thermal properties. The thermal resistance was found to be up to 90% lower than that of a comparable solid copper plate. Thus, a hot part with defined heating power would remain at a much lower temperature level and, for the same heater temperature, a much larger heating power could be applied. Moreover, the dependence of PHP operation and thermal properties on water and air cooling, condenser area size and orientation is examined. Under some test configurations, dryout conditions are observed which could be avoided by choosing an appropriate size for the fluid channels, heater and condenser.

Films of zwitterionic polymers are increasingly explored for conferring fouling resistance to materials. Yet, the structural diversity of polyzwitterions is rather limited so far, and clear structure-property relationships are missing. Therefore, we synthesized a series of new polyzwitterions combining ammonium and sulfate groups in their betaine moieties, so-called poly(sulfabetaine)s. Their chemical structures were varied systematically, the monomers carrying methacrylate, methacrylamide, or styrene moieties as polymerizable groups. High molar mass homopolymers were obtained by free radical polymerization. Although their solubilities in most solvents were very low, brine and lower fluorinated alcohols were effective solvents in most cases. A set of sulfabetaine copolymers containing about 1 mol % (based on the repeat units) of reactive benzophenone methacrylate was prepared, spin-coated onto solid substrates, and photo-cured. The resistance of these films against the nonspecific adsorption by two model proteins (bovine serum albumin—BSA, fibrinogen) was explored, and directly compared with a set of references. The various polyzwitterions reduced protein adsorption strongly compared to films of poly(n‑butyl methacrylate) that were used as a negative control. The poly(sulfabetaine)s showed generally even somewhat higher anti-fouling activity than their poly(sulfobetaine) analogues, though detailed efficacies depended on the individual polymer–protein pairs. Best samples approach the excellent performance of a poly(oligo(ethylene oxide) methacrylate) reference.