The design of gear pumps and motors is focused on more efficient units which are possible to achieve using advanced numerical simulation techniques. The flow that appears inside the gear pump is very complex, despite the simple design of the pump itself. The identification of fluid flow phenomena in areas inside the pump, considering the entire range of operating parameters, is a major challenge. This paper presents the results of simulation studies of leakages in axial and radial gaps in an external gear pump carried out for different gap shapes and sizes, as well as various operating parameters. To investigate the processes that affect pump efficiency and visualize the fluid flow phenomena during the pump’s operation, a CFD model was built. It allows for a detailed analysis of the impact of the gears’ eccentricity on leakages and pressure build-up on the circumference. Performed simulations made it possible to indicate the relationship between leakages resulting from the axial and radial gap, which has not been presented so far. To verify the CFD model, experimental investigations on the volumetric efficiency of the external gear pump were carried out. Good convergence of results was obtained; therefore, the presented CFD model is a universal tool in the study of flow inside external gear pumps.
14 April 2022 in IEEE Transactions on Vehicular Technology
As a typical energy storage in hydraulic hybrid powertrain, the hydraulic accumulator has high power density but low energy density. There are some efforts in improving the energy density of hydraulic energy storage to achieve balanced performance. Therefore in this study an electric-hydrostatic energy storage system is proposed to replace hydraulic accumulator in a hydraulic hybrid wheel loader. Through active control of proposed energy storage, constant system pressure is possible to provide good vehicle drivability. A rule-based energy management strategy without estimating final drive power is proposed. The vehicle performance and fuel consumption with different constant system pressures are studied. Results show the vehicle fuel consumption is reduced by 5.9% with constant system pressure reduced from 33 to 27 MPa. The energy density and power density of proposed energy storage are calculated, showing a much higher energy density and slightly lower power density than gas-charged accumulator.
The ongoing shift towards hybrid and electric vehicles has a strong impact on noise and vibration engineering. New, complex dynamic phenomena are brought to vehicle user attention due to the absence of internal combustion engines and the significant role in vehicle and drive feel perception. This paper presents an FEM (Finite Element Method) dynamic simulation model of an automotive Electric Power Steering assembly. Preliminary modal simulations and experiments as well as field data replication techniques were implemented to identify the phenomena and prepare and validate model components. A full dynamic model of an Electric Power Steering was presented, and fine-tuned including the presence of lubrication at the gear mesh interface. Experimental investigations were conducted alongside FEM simulations for various model setups. Linear and nonlinear contact stiffness models were implemented, as well as contact damping, and simulated at chosen assembly interfaces. The results indicated that in the case of NVH (Noise Vibration and Harshness) analysis of shock/impact originating problems, contact parameters used for static, quasi-static, and low velocity analyses were not applicable. Nonlinear and damped contact stiffness provided better results in such a case.
The article presents an innovative design solution of a balanced vane pump integrated with an electric motor that has been developed by the authors. The designed and constructed bench, which enables testing of the system: power supply, converter, ntegrated motor—pump assembly and hydraulic load at different motor speeds and different pressures in the hydraulic system, is described. The electromagnetic and hydraulic processes in the motor-pump unit are investigated, and new, previously unpublished, results of experimental studies at steady and dynamic states are presented. The results of the study showed good dynamics of the integrated motor-pump assembly and proved its suitability to control the pump flow rate, and thus, the speed of the hydraulic cylinder or the speed of the hydraulic motor.
A mathematical modeling approach to determine fluid film thickness on the vane tip in a vane pump transmission is developed. The transmission is based on a double-acting vane pump with an additional output shaft coupled to a floating ring. Owing to the floating ring design, the internal viscous friction helps to drive the output shaft, whereas the friction is turned into heat in a conventional vane pump. To study the mechanical efficiency, it is crucial to investigate the fluid film thickness between the vane tip and the ring inner surface. The modeling approach in this study takes the interactions between vane radial motion and chamber pressure dynamics into consideration, without using a computational fluid dynamics approach. The lubrication on the vane tip is considered as elasto-hydrodynamic lubrication and the fluid film thickness calculation is based on the Hooke lubrication diagram. Results show that the developed simulation model is capable of revealing the fluid film thickness change and vane radial motion in different operation regions. Sensitivity studies of several parameters on the minimum fluid film thickness are also presented.
In the slider-crank mechanism, where the rotational motion is transformed into the translational motion, the input torque is highly variable due to the inertial effect. The consequence of fluctuating torque is that it causes the load upon the prime mover to be inconsistent, which might likely results in higher stresses in the components, higher joint friction, and the necessity for higher driving power. In this paper, a technique of reduction of the dynamic torque and joint forces in the slider-crank mechanism using mechanical resonance is described. A comparative result of the conventional system in the process of gas compression, as a practical application example, is presented. The result shows that the utilization of resonance has the advantage of providing lower dynamic torque and rotating joint forces compared to the conventional operation. Since the compression of the air itself takes effect as a spring compression, in the gas compression process, the narrow torque and force region around the resonant frequency can be obtained with or without the use of spring as the element for storing the potential energy.