The article presents an innovative design solution of a balanced vane pump integrated with an electric motor that has been developed by the authors. The designed and constructed bench, which enables testing of the system: power supply, converter, ntegrated motor—pump assembly and hydraulic load at different motor speeds and different pressures in the hydraulic system, is described. The electromagnetic and hydraulic processes in the motor-pump unit are investigated, and new, previously unpublished, results of experimental studies at steady and dynamic states are presented. The results of the study showed good dynamics of the integrated motor-pump assembly and proved its suitability to control the pump flow rate, and thus, the speed of the hydraulic cylinder or the speed of the hydraulic motor.
8 May 2009 in COMPEL - The international journal for computation and mathematics in electrical and electronic engineering
Purpose – The purpose of this paper is to present a developed modelling method of a car starter with permanent magnet commutator motor. Design/methodology/approach – Mathematical model, algorithm and computational program of electrical and mechanical quantities transients in the system: battery – car starter with permanent magnet commutator motor and planetary gear – combustion engine were developed. Circuit-field method was applied. Magnetic quantities determined using time-stepped finite-element method (with the help of Maxwell software) were used as the parameters of mathematical model equations in circuital part. Program was developed in the Matlab environment. Findings – The developed mathematical model, the algorithm and the program enable the computations of transients of electrical and mechanical quantities at different ambient temperature, by different swept capacity of the combustion engine as well as by different battery capacity and different charge ratio. Research limitations/implications – The analysis was carried out on an example of four-cylinder combustion engine. However, the developed modelling method can be used for analysis of different combustion engines start-up. Practical implications – The proposed modelling method is useful for analysis of car starters at the stage of design. Originality/value – The originality of the work consist in the fact that in the developed model variation of the car starter load torque as well as the variations of the entire mechanical system moment of inertia were taken into account.
The paper investigates an alternative approach to measuring and compensating reactive power in electric machines, particularly under non-sinusoidal voltage and current waveforms. Traditional power definitions, such as those introduced by Budeanu and Fryze, as well as the power triangle, are discussed alongside integral definitions of reactive power, which account for waveform distortions. This approach is novel and has not been previously applied in the context of electric machines. A digital algorithm for reactive power calculation, based on the integral definition, is proposed. It requires minimal computational resources and is easy to implement. Experimental measurements conducted on a single-phase induction motor demonstrate the impact of capacitive compensation on current waveforms. The results confirm the validity of the adopted definition of reactive power. With full reactive power compensation, the RMS value of the current drawn by the motor is minimized, which is not always the case with the classical approach to improving the power factor. The findings highlight the importance of accurate reactive power measurement and compensation in enhancing the performance and energy efficiency of electrical machines. The proposed approach is applicable not only to single-phase motors but also more broadly in determining the reactive power drawn by electric machines and in measuring electric energy, particularly in the presence of distorted voltages and currents.
The paper presents the developed drive system with a brushless DC (BLDC) motor, for which laboratory tests have been performed. Research has been carried out for two speed control methods: using an inverter (by pulse width modulation) and controlling the voltage value applied to the converter. Laboratory tests of the drive system have been performed on the developed research stand. Waveforms of electrical and mechanical quantities as well as operating parameters of the drive system have been measured and compared for both ways of speed control.
Field-circuit model of a brushless DC motor with speed control using PWM method was developed. Waveforms of electrical and mechanical quantities of the designed motor with a high pressure vane pump built in a rotor of the motor were computed. Analysis of electromagnetic phenomena in the system: single phase AC network – converter - BLDC motor was carried out.
19 November 2018 in Archives of Electrical Engineering
An analysis of the influence of inverter PWM speed control methods on the operation of a brushless DC (BLDC) motor was carried out. Field-circuit models of the BLDC motor were developed taking into account rotational speed control by two classic methods: the unipolar H_ON_L_PWM and the bipolar H_PWM_L_PWM. Waveforms of the electrical and mechanical quantities and the motor parameters were computed. The results of the computations were verified by measurements performed on a specially designed test stand. On the basis of the measuredwaveforms of the electrical and mechanical quantities the dependence of the drive system efficiencies and power losses on rotational speed was determined for the two methods of inverter control.