The development of analytical methods for viscoelastic fluid flows is challenging. Currently, this problem has been solved for particular cases of multimode differential rheological equations of media state (Giesekus, the exponential form of Phan-Tien-Tanner, eXtended Pom-Pom). We propose a parametric method that yields solutions without additional assumptions. The method is based on the parametric representation of the unknown velocity functions and the stress tensor components as a function of coordinate. Experimental flow visualization based on the SIV (smoke image velocimetry) method was carried out to confirm the obtained results. Compared to the Giesekus model, the experimental data are best predicted by the eXtended Pom-Pom model.
A two-dimensional mathematical model for a steady viscoelastic laminar flow in a confusor was developed under the condition of swirled flow imposed at the inlet. Low density polyethylene was considered as a working fluid. Its behavior was described by a two-mode Giesekus model. The proposed mathematical model was tested by comparing it with some special cases presented in the literature. Additionally, we propose a system of equations to find the nonlinear parameters of the multimode Giesekus model (mobility factor) based on experimental measurement. The obtained numerical results showed that in a confusor with the contraction rate of 4:1, an increase in the swirl intensity at Wi < 5.1 affects only the circumferential velocity, while the axial and radial velocities remain constant. The distribution pattern of the first normal stress difference in the confusor is qualitatively similar to the one in a channel with abrupt contraction, i.e., as the viscoelastic fluid flows in the confusor, the value of N1 increases and reaches a maximum at the end of the confusor. Dimensionless damping coefficients of swirl are used to estimate the swirl intensity. The results show that the swirl intensity decreases exponentially.
The parametric solution to the problem of flow of multimode viscoelastic fluids with the Giesekus and Phan-Thien–Tanner models in a circular pipe is given in the case of laminar isothermal steady-state flow regimes at moderate and high Weissenberg numbers. The distributions of the axial velocity and the normal stresses are presented. In addition, the distributions of the first normal stress coefficients for flow of the low-density polyethylene (DSM Stamylan LD 2008 XC43) and a 0.25% aqueous polyacrylamide solution are analyzed. The experimental and calculated data are in the adequate agreement for both (Giesekus and Phan-Thien–Tanner) rheological models. A particular case of the Giesekus viscoelastic fluid flow with the rheological model parameter in the interval (0.5, 1) is considered.
The results of the numerical calculations of isothermal viscous flows in convergent-divergent channels axially rotating at a constant angular velocity are presented. With reference to the example of the calculations performed at Re = 2000 the difference in the flowfields in a fixed channel and that rotating at an angular velocity Ω = 10 s in analyzed. The results of the calculations of viscous flows in convergent-divergent channels at Re = 2000 and Ω = 10 s are also presented.
The helical coordinate system is used for mathematical description of laminar viscous fluid flows in channels with three helical fins of annular gap. The mathematical model in which the equations of...
Flow in a prismatic channel of the melts of the SKI-3 and SKMS30-ARKM-15-based rubber mixtures widely used in the chemical industry is numerically investigated. The description of these media, which exhibit viscoelstic properties when being processed, requires a particular approach that would take their rheological behavior and various anomalies into account. Amidst many rheological equations governing flows of rheologically complex media the equation that would ensure not only the good reliability of the results but also the feasibility in its practical use should be selected. The special features of viscoelastic fluids clearly manifest themselves in the flow in a prismatic channel of a noncircular cross-section. Secondary flows characteristic of the viscoelastic flows in such channels force the fluid particles to move in spiral trajectories along the channel. In the numerical calculations the Phan-Thien–Tanner (PTT) rheological model is used; its parameters are obtained on the basis of experimental data. The calculations are performed using the COSMOL Multiphysics software complex. the method of solution was tested against the analytical solution of the PTT fluid flow in a round tube which was compared with the numerical solution.