LIDAR (Light Detection and Ranging) sensors are one of the leading technologies that are widely considered for autonomous navigation. However, foggy and cloudy conditions might pose a serious problem for a wide adoption of their use. Polarization is a well-known mechanism often applied to improve sensors’ performance in a dense atmosphere, but is still not commonly applied, to the best of our knowledge, in self-navigated devices. This article explores this issue, both theoretically and experimentally, and focuses on the dependence of the expected performance on the atmospheric interference type. We introduce a model which combines the well-known LIDAR equation with Stocks vectors and the Mueller matrix formulations in order to assess the magnitudes of the true target signal loss as well as the excess signal that arises from the scattering medium radiance, by considering the polarization state of the E–M (Electro-Magnetic) waves. Our analysis shows that using the polarization state may recover some of the poor performance of such systems for autonomous platforms in low visibility conditions, but it depends on the atmospheric medium type. This conclusion is supported by measurements held inside an aerosol chamber within a well-controlled and monitored artificial degraded visibility atmospheric environment. The presented analysis tool can be used for the optimization of design and trade-off analysis of LIDAR systems, which allow us to achieve the best performance for self-navigation in all weather conditions.
14 December 2020 in Journal of Occupational and Environmental Hygiene
Simple plastic face shields have numerous practical advantages over regular surgical masks. In light of the spreading COVID-19 pandemic, the potential of face shields as a substitution for surgical masks was investigated. In order to determine the efficacy of the protective equipment we used a cough simulator. The protective equipment considered was placed on a manikin head that simulated human breathing. Concentration and size distribution of small particles that reached the manikin respiration pathways during the few tens of seconds following the cough event were monitored. Additionally, water sensitive papers were taped on the tested protective equipment and the manikin face. In the case of frontal exposure, for droplet diameter larger than 3 μm, the shield efficiency in blocking cough droplets was found to be comparable to that of regular surgical masks, with enhanced protection for portions of the face that the mask does not cover. Additionally, for finer particles, down to 0.3 µm diameter, a shield blocked about 10 times more fine particles than the surgical mask. When exposure from the side was considered, the performance of the shield was found to depend dramatically on its geometry. While a narrow shield allowed more droplets and aerosol to penetrate in comparison to a mask under the same configuration, a slightly wider shield significantly improved the performance. The source control potential of shields was also investigated. A shield, and alternatively, a surgical mask, were placed on the cough simulator, while the breathing simulator, situated 60 cm away in the jet direction, remained totally exposed. In both cases, no droplets or particles were found in the vicinity of the breathing simulator. Conducted experiments were limited to short time periods after expiratory events, and do not include longer time ranges associated with exposure to suspended aerosol. Thus, additional evidence regarding the risk posed by floating aerosol is needed to establish practical conclusions regarding actual transmittance reduction potential of face shields and surgical face masks.
Halo-Photonics StreamLine XR Doppler LiDAR measurements are performed using several scan configurations (Velocity Azimuth Display-VAD and Doppler Beam Swing-DBS) and elevation angles of 60° and 80°. The measurements are compared to wind observations conducted by various in situ instruments (tethered balloon, meteorological mast, and radiosondes). Good agreement is obtained, with R2 over 0.90 for wind speed and a standard error ≤ 18.6° for wind direction. The best performance was attained for lower elevation scans (60°), which is consistent with the higher spatial horizontal homogeneity exhibited by lower angle scans. VAD and DBS scans performed almost equally well with slight advantage for VAD in higher altitudes and for DBS for lower altitudes. The boundary layer structure along a diurnal cycle is analyzed by utilizing retrieved backscatter data and wind measurements in conjunction with Weather Research and Forecast (WRF) simulations. The presence of multiple inversions which allow the coexistence of different layers within the studied profile is also verified using data acquired by several radiosondes. Synergic use of LiDAR data with WRF simulations for low SNR regions is demonstrated.
This study describes comprehensive measurements performed for four consecutive nights during a regional-scale radiation fog event in Israel’s central and southern areas in January 2021. Our data included both in situ measurements of droplets size distribution, visibility range, and meteorological parameters and remote sensing with a thermal IR Whole Sky Imager and a Doppler Lidar. This work is the first extensive field campaign aimed to characterize fog properties in Israel and is a pioneer endeavor that encompasses simultaneous remote sensing measurements and analysis of a fog event with a thermal IR Whole Sky Imager. Radiation fog, as monitored by the sensor’s field of view, reveals three distinctive properties that make it possible to identify it. First, it exhibits an azimuthal symmetrical shape during the buildup phase. Second, the zenith brightness temperature is very close to the ground-level air temperature. Lastly, the rate of increase in cloud cover up to a completely overcast sky is very fast. Additionally, we validated the use of a Doppler Lidar as a tool for monitoring fog by proving that the measured backscatter-attenuation vertical profile agrees with the calculation of the Lidar equation fed with data measured by in situ instruments. It is shown that fog can be monitored by those two, off-the-shelf-stand-off-sensing technologies that were not originally designed for fog purposes. It enables the monitoring of fog properties such as type, evolution with time and vertical depth, and opens the path for future works of studying the different types of fog events.
Simple plastic face shields have many advantages compared to regular medical masks. They are easily cleaned for reuse and comfortable to wear. In light of the spreading COVID-19 pandemic, the potential of face shields as a substitution for medical masks, as a recommendation to the general population, was tested. Testing the efficacy of the protective equipment utilized a cough simulator that was carefully tuned to replicate human cough in terms of droplet size distribution and outlet velocity. The tested protective equipment was worn on a manikin head simulating human breathing. An Aerodynamic Particle Sizer (APS) was used to analyze the concentration and size distribution of small particles that reach the manikin head respiration pathways. Additionally, Water sensitive papers were taped over and under the tested protective equipment, and were subsequently photographed and analyzed. For droplets larger than 3μm by diameter, the efficiency of shields to block cough droplets was found to be comparable to that of regular medical masks, with enhanced protection on face parts the mask does not cover. Additionally, for finer particles, of the order 0.3 to few microns, a shield was found to perform even better, blocking about 10 times more fine particles than the medical mask. This implies that for the general population that is not intendedly exposed to confirmed infected individuals, recommending the use of face shields as an alternative to medical masks should be considered.
Foggy and cloudy conditions, are considered to be a serious problem for the assimilation of the use of LIDAR and imaging sensors into autonomous mobile platforms. Our work explores, both theoretically and experimentally, how the consideration of the polarization state affects the performance of such systems for autonomous platforms in low visibility conditions.