Photovoltaic systems represent a leading part of the market in the renewable energies sector. Contemporary technology offers possibilities to improve systems converting sun energy, especially for the efficiency of modules. The paper focuses on current concentrated photovoltaic (CPV) technologies, presenting data for solar cells and modules working under lab conditions as well as in a real environment. In this paper, we consider up-to-date solutions for two types of concentrating photovoltaic systems: high-concentration photovoltaics (HCPV) and low-concentration photovoltaics (LCPV). The current status of CPV solar modules was complemented by the preliminary results of new hybrid photovoltaic technology achieving records in efficiency. Compared to traditional Si-PV panels, CPV modules achieve greater conversion efficiency as a result of the concentrator optics applied. Specific CPV technologies were described in terms of efficiency, new approaches of a multijunction solar cell, a tracking system, and durability. The results of the analysis prove intensive development in the field of CPV modules and the potential of achieving record system efficiency. The paper also presents methods for the determination of the environmental impact of CPV during the entire life cycle by life cycle assessment (LCA) analysis and possible waste management scenarios. Environmental performance is generally assessed based on standard indicators, such as energy payback time, CO₂ footprint, or GHG emission.

The paper presents a review of End-of-Life scenarios (EoL) (disposal, incineration, chemical, thermal and mechanical recycling) compared to the production stage of Fibre-Reinforced Polymers (FRPs) of composites regarding global warming potential. Innovative FRP manufacturing technologies (vacuum infusion, ultraviolet curved pultrusion, hot stamping, three-dimensional printing and automatic tape placement) commonly used in the shipbuilding industry were environmentally assessed. The materials, energy flows and waste discharged to the environment over the whole life cycle were collected, identified and quantified based on Life Cycle Assessment (LCA) analysis in the frame of the Fibre4Yards project. The results of LCA calculations show that waste management (the EoL scenario) contributes 5 to 39% of the total carbon footprint for FRP technologies. The highest contribution of the EoL scenario was found for technologies where polypropylene was applied, i.e., 33 and 38% of the total CO₂ emissions. Our analysis of the literature and information from industrial partners confirm that the standard and most common waste scenario for FRP materials and compounds is still incineration and landfilling.

Life cycle assessments (LCAs) can provide insights into the environmental impact of production processes. In this study, a comparative LCA was performed for the synthesis of 2’3’‐cyclic GMP‐AMP (2’3’‐cGAMP) in an early development stage. The cyclic dinucleotide (CDN) is of interest for pharmaceutical applications such as cancer immunotherapy. CDNs can be synthesized either by enzymes or chemical catalysis. It is not known which of the routes is more sustainable as both routes have their advantages and disadvantages, such as a poor yield for the chemical synthesis and low titers for the biocatalytic synthesis. The synthesis routes were compared for the production of 200 g 2’3’‐cGAMP based on laboratory data to assess the environmental impacts. The biocatalytic synthesis turned out to be superior to the chemical synthesis in all considered categories by at least one magnitude, for example, a global warming potential of 3055.6 kg CO₂ equiv. for the enzymatic route and 56454.0 kg CO₂ equiv. for the chemical synthesis, which is 18 times higher. This study demonstrates the value of assessment at an early development stage, when the choice between different routes is still possible.

Life cycle assessment (LCA) is used to evaluate the environmental load of fibre composite manufacturing technologies in the shipyards industry in a frame of the Fibre4Yards (Horizon 2020) project. This paper is focused on the LCA of fibre-reinforced polymer (FRP) technologies used to produce all elements of the floating unit, i.e., the conventional vacuum infusion technology for the deck panel and adaptive mould process for superstructure panels, ultraviolet (UV) curved pultrusion process for the production of stiffeners, hot stamping technology for brackets, and three-dimensional (3D) printing and automatic tape placement (ATP) for pillars. Environmental impact was assessed based on standard indicators: Global Warming Potential, water consumption, and fossil resource scarcity. The results indicate that the total carbon footprint of analysed FRP technologies is mainly produced by the type of the materials applied rather than by the amount of energy consumed during the process.

The aim of the presented research was to examine the concentration of biogenic compounds and heavy metals in the bottom sediments of the Sulejów Reservoir (Central Poland) from October 2018. Based on the obtained research results, maps of the spatial distribution were prepared. The following parameters were analyzed: total phosphorus (TP), total Kjeldahl nitrogen, total organic carbon (TOC), ratio of total organic carbon to nitrogen (C:N), organic matter content as well as Cd, Cr and Pb concentrations. The sediments were collected at 28 sampling sites, covering the whole area of the reservoir. The differences in the content of individual biogenic compounds result from the composition of the debris applied by the supplying rivers, as well as the content of this elements in the water, long retention time (40 days) and depth from which the tested sediments were taken. The distribution of examined compounds was largely influenced by the agricultural activity in the studied area, as well as the presence of ports and recreational points. Based on the measurements, the highest amounts of biogenic components deposit in sediments of deep parts in slow-flowing waters, in stagnation zones, areas adjacent to arable land, and the sites where fine-size fractions prevail in the deposited material. Biogenic compounds in sediments of the Sulejów Reservoir showed a pattern of gradual increase along the reservoir from lower values in the back-water part. A similar relationship is visible for heavy metals. Referring to the ecotoxicological criteria, it can be stated that bottom sediments from the Sulejów Reservoir collected in 2018 are not toxicologically contaminated in terms of cadmium, lead and chromium content.

The aim of this work is to evaluate core variables of the ecological potential of the Sulejów Reservoir (temperature distribution, flow velocities, and concentrations of selected indicators, e.g., phosphates, nitrates, the abundance of phytoplankton) using a three-dimensional hydrodynamic model, GEMSS-HDM (generalized environmental modeling system for surface waters), coupled with a water quality model, WASP EUTRO (GEMSS-WQM). The monitoring data necessary to build the model were obtained from two multiparameter probes that were submerged in two locations in the Sulejów Reservoir. An ADCP current profiler was used to collect data for hydrodynamic model calibration and verification. Total error between computed and measured velocity was estimated at 10–15%. A high concentration of chlorophyll-a during the vegetation season of 2015 (0.02 mg/L) was coupled with high water temperature (above 25 °C) and low concentrations of biogenic compounds (phosphorus and nitrogen at 0.02 and 0.001 mg/L, respectively). In 2015, NO₃-N was the limiting nutrient in the Sulejów Reservoir. Maximum growth of algae was observed in June and July 2015 (0.02 mg/L chla) along the entire length of the reservoir; algae bloom volume reduction was observed in September (0.004 mg/L chla). Proposed scenarios for nutrient reduction—50% reduction of phosphate-phosphorus (PO₄-P) and nitrate-nitrogen (NO₃-N) from agriculture areas as well as 50% reduction of discharges from septic tanks—led to a considerable reduction of nutrient concentrations in the reservoir waters; it additionally favors reducing the concentration of chlorophyll-a. The obtained results indicate that these sources of pollutants are mainly responsible for the poor water quality status of the reservoir and more intensive eutrophication phenomena.