As the near surface deposits are being mined out, underground mines will increasingly operate at greater depths. This will increase the challenges related to transporting materials from deeper levels to the surface. For many years, the ore and waste transportation from most deep underground mines has depended on some or all of the following: truck haulage, conveyor belts, shafts, rails, and ore pass systems. In sub-level caving, and where ore passes are used, trains operating on the main lower level transport the ore from ore passes to a crusher, for subsequent hoisting to the surface through the shaft system. In many mines, the use of the ore pass system has led to several problems related to the ore pass availability, causing production disturbances and incurred cost and time for ore pass rehabilitation. These production disturbances have an impact on the mining activities since they increase the operational costs, and lower the mine throughput. A continued dependency on rock mass transportation using ore passes will generate high capital costs for various supporting structures such as rail tracks, shaft extensions, and crushers for every new main level. This study was conducted at an existing underground mine and analyzed the transport of ore from loading areas at the lower levels up to the existing shaft points using trucks without employing ore passes. The results show that, when the costs of extending ore passes to lower levels become too great or ore passes cannot be used for production, haul trucks can be a feasible alternative method for transport of ore and waste up the ramp to the existing crusher located at the previous main level. The use of trucks will avoid installing infrastructure at the next main level and extending the ore passes to lower levels, hence reducing costs.
Ore passes are often the main part of sublevel caving transportation systems, and they use gravity to move material to lower levels in the mine. During operations, the ore pass structures are exposed to the risk of stoppage and failure, leading to a long-term reduction in operational capacity and affecting productivity. The failed ore passes can be restored or rehabilitated, but the rehabilitation cost is normally high and the time to restore is usually long. To minimize disturbances and stoppage of the ore pass, alternative strategies should be considered. The appropriate design and operation of an ore pass is crucial. Therefore, this study compared running ore pass systems in a filled, near-empty, or flow-through manner using discrete event simulation. The aim was to compare the ore pass operational performance and impact on reaching the daily and 90-day production targets of 76.4 Ktonnes and 6.9 Mtonnes, respectively. The results showed that running the ore pass in flow-through mode, filled manner, and near-empty manner achieved 96%, 80%, and 81% of the production target, respectively. In mining operations where ore pass systems are used to transfer material, running them in a flow-through mode can ensure higher production and fewer hang-ups, as it lessens the chance of blocks arching over a chute throat and leads to less blasting.
4 December 2024 in Mining, Metallurgy & Exploration
Diesel-powered load haul dump machines have been the backbone of underground mining loading and hauling operations for over six decades. However, as mines get deeper, and regulations become more rigorous, the adoption of battery electric vehicles (BEVs) has the potential to enhance energy efficiency and provide a healthier environment for miners. Electric engines have a significantly higher energy efficiency and produce no exhaust gases or diesel particulate matter. The use of BEVs in underground operations introduces additional factors to consider, such as battery swapping and the required number of batteries, swapping, and charging stations. This study conducted a discrete event simulation using Arena simulation software with a focus on queueing and its relationship to different numbers of machines, batteries, and swapping times in an underground block cave mine. The results suggest that when there are six, eight, or 12 LHDs and four swapping and charging stations with an unlimited number of batteries, the queueing time to swap the batteries remains minimal. In scenarios with eight LHDs and a limited number of batteries, depending on the battery swapping time, 2–2.5 batteries per machine are required to achieve maximum production with minimal queueing. However, when there are too few batteries, queueing becomes significant. Moreover, when the number of working groups (machines going for a battery swap around the same time) is less than the ratio between the battery operational time and the swapping time, the queueing remains low.
30 June 2021 in Journal of the Southern African Institute of Mining and Metallurgy
Today's mining operations require fast reporting and rapid rescheduling based on updated information. An automatic mine scheduling system could not only quickly reschedule but also propose alternative solutions. To avoid the financial and physical risks associated with testing such a system directly in operation, it could be first evaluated via discrete event simulation models. This would offer a safe environment to evaluate different operating rules and algorithms. In this study, this is achieved by integrating automatic scheduling software with a discrete event simulation model.