Igor Bezukladnikov

Dr. Igor Bezukladnikov


Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 August 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
AOAlexander Andreevich Oskolkov
Alexander Andreevich Oskolkov
IBIgor Bezukladnikov
Igor Bezukladnikov
DTDmitriy Trushnikov
Dmitriy Trushnikov
An approach for improving and maintaining consistent fusion quality of the deposited material during FDM 3d-printing is proposed. This approach is based on the nozzle temperature control during the printing process to adjust the polymer extrusion temperature with a speed and accuracy adequate to the FDM process. High frequency induction heating of the lightweight nozzle (<1 g) was used. To control the temperature of a lightweight nozzle, the resonant temperature measurement method based on the analysis of the high frequency eddy currents is proposed. To determine the parameters of the nozzle and the inductor as a plant, a FEM model of the inductive heating of the nozzle and a simulated model of a serial-parallel resonant circuit containing inductor were developed. Linearization of the automatic control system was performed to ensure the equal quality of regulation when operating in a wide temperature range. The quality of regulation, stability of the system, and coefficients of the PID controller were evaluated using a simulated model of the control system. A number of test samples were printed from various materials, and tensile stress testing was carried out. The developed control method reduces the nozzle temperature control error from 20 to 0.2 °C and decreases control delay by more than six times.

24 November 2023 in Polymers
Verified
Journal Article
Open access
PDF file
AOAlexander Andreevich Oskolkov
Alexander Andreevich Oskolkov
IBIgor Bezukladnikov
Igor Bezukladnikov
DTDmitriy Trushnikov
Dmitriy Trushnikov
An approach for improving and maintaining a consistent weld quality of the deposited material during the FFF printing process is proposed. The approach is based on the analysis of the printing process thermal cycle and the real-time nozzle temperature control. The mathematical model of the FFF printing process has been developed with the use of real-time control in the algorithm of numerical implementation. The successful solution of the thermal conductivity problem made it possible to determine segment-wise heating settings for use during the printing process, resulting in a high and stable quality of welding. Comparison of the results of modeling with other well-known mathematical models of the FFF printing process and experimental results showed the adequacy of the proposed model. A maximum deviation of 17.7% between the simulation results and the thermography data was observed. The proposed model was verified using rectangular 3D polylactide shapes printed with and without regulation of the power of the heat source according to the previously estimated settings. The overall quality of regulation, stability of the system, and the PI coefficients of the controller were evaluated using a simulated model of the control system. The results of the experiment fully correspond with the modeling results.

6 April 2021 in Sensors
Verified
Journal Article
Open access
PDF file
AOAlexander Andreevich Oskolkov
Alexander Andreevich Oskolkov
IBIgor Bezukladnikov
Igor Bezukladnikov
DTDmitriy Trushnikov
Dmitriy Trushnikov
One of the biggest challenges of fused deposition modeling (FDM)/fused filament fabrication (FFF) 3D-printing is maintaining consistent quality of layer-to-layer adhesion, and on the larger scale, homogeneity of material inside the whole printed object. An approach for mitigating and/or resolving those problems, based on the rapid and reliable control of the extruded material temperature during the printing process, was proposed. High frequency induction heating of the nozzle with a minimum mass ( 300 W) heating system, an indirect (eddy current) temperature measurement method was proposed. It is based on dynamic analysis over various temperature-dependent parameters directly in the process of heating. To ensure better temperature measurement accuracy, a series-parallel resonant circuit containing an induction heating coil, an approach of desired signal detection, algorithms for digital signal processing and a regression model that determines the dependence of the desired signal on temperature and magnetic field strength were proposed. The testbed system designed to confirm the results of the conducted research showed the effectiveness of the proposed indirect measurement method. With an accuracy of ±3 °C, the measurement time is 20 ms in the operating temperature range from 50 to 350 °C. The designed temperature control system based on an indirect measurement method will provide high mechanical properties and consistent quality of printed objects.

30 June 2017 in Vestnik of Volga State University of Technology. Series Radio Engineering and Infocommunication Systems
Verified
Journal Article
Closed access
IBIgor Bezukladnikov
Igor Bezukladnikov
AMAnna Mironova
Anna Mironova
AYAleksandr Yuzhakov
Aleksandr Yuzhakov

30 June 2016 in Vestnik of Volga State University of Technology. Series Radio Engineering and Infocommunication Systems
Verified
Journal Article
Closed access
IBIgor Bezukladnikov
Igor Bezukladnikov
EKEfim Kon
Efim Kon
AYAleksandr Yuzhakov
Aleksandr Yuzhakov

1 September 2025 in Russian Engineering Research
Verified
Journal Article
Closed access
PDF file
EFE. A. Fokeev
E. A. Fokeev
SVS. V. Varushkin
S. V. Varushkin
IBIgor Bezukladnikov
Igor Bezukladnikov
VBV. Ya. Belen’KIi
V. Ya. Belen’KIi
AYA. A. Yuzhakov
A. A. Yuzhakov
DTDmitriy Trushnikov
Dmitriy Trushnikov
A system for wire supply in electron beam additive surfacing is proposed. This system ensures high accuracy in wire supply to the electron beam and effecti